ctr_mcu/trunk/task_debug.c
n2232 28d501e219 ■2.0Dテスト
(バグ修正)電池が無くて、アダプタ有りの時、電源を入れようとしていた(すぐに電圧低くて切れる)。修正。
(バグ修正)wdtリセット後、電源が切れてしまっていた。hdwinit2の設定ミス。
(バグ修正?)ヒューズ切れ時、充電LEDが点きっぱなしになってしまったのを回避
(バグ修正)アダプタをさして、電池を付けてから起動すると、ステータスが充電中にならなかったのを修正
(リファクタリング?)DI_wt_chk()をDI()に。上手にマクロが書けなかった。そのうち?
もういらない #if 0 を少し削除、残す物にはコメント追加
rtc.c、インターバルのフラグを+1ではなく、=1にした。wait_ms(100)などしたときに50回タスクが回ってしまう。インターバルを当てにしてウェイトにしていることがあるので、多少コマ落ちしても間隔を守る


git-svn-id: file:///Volumes/Transfer/gigaleak_20231201/2020-05-23%20-%20ctr.7z%20+%20svn_v1.068.zip/ctr/svn/ctr_mcu@399 013db118-44a6-b54f-8bf7-843cb86687b1
2011-08-31 11:43:44 +00:00

113 lines
3.0 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

#ifndef _WIN32
#pragma SFR
#pragma NOP
#pragma HALT
#pragma STOP
#endif
#include "incs_loader.h"
//#include "incs.h"
#include "renge\renge.h"
#include "pm.h"
#include "accero.h"
/* ========================================================
======================================================== */
// 7セグ 4バイト版
# define IIC_SLA_DBG_MONITOR 0x44
#if 0 // デバッグモニタ用タスク
注意! タスクリストからも外してますので、使うなら復活させて下さい!
void tsk_debug( )
{
// u8 temp;
/*
if( system_status.pwr_state == ON_TRIG ){
{
static u8 count = 0;
// デバッグLED8bitの初期化
temp = iic_mcu_read_a_byte( IIC_SLA_8LEDS, IIC_8LEDS_REG_DO );
count ++;
iic_mcu_write_a_byte( IIC_SLA_8LEDS, IIC_8LEDS_REG_DO, count );
iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 3, count );
}
}
*/
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 2, vreg_ctr[ VREG_C_IRQ1 ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 1, boot_ura );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 1, vreg_ctr[ VREG_C_SND_VOL ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 1, vreg_ctr[ VREG_3D ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 0, vreg_ctr[ VREG_C_ACC_ZH ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 3, vreg_ctr[ VREG_C_3D ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 2, vreg_ctr[ VREG_C_SND_VOL ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 1, vreg_ctr[ VREG_C_STATUS ] );
// iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 0, vreg_ctr[ VREG_C_ACC_ZH ] );
/*
{
u8 str[4];
if( ( system_status.pwr_state == ON ) || ( system_status.pwr_state == SLEEP ) )
{
str[3] = vreg_ctr[ VREG_C_FREE0 ];
str[2] = vreg_ctr[ VREG_C_FREE1 ];
str[1] = vreg_ctr[ VREG_C_STATUS ];
str[0] = vreg_ctr[ VREG_C_RTC_SEC ];
str[3] = vreg_ctr[ VREG_C_SND_VOL ];
str[2] = vreg_ctr[ VREG_C_3D ];
str[1] = vreg_ctr[ VREG_C_ACC_CONFIG ];
str[0] = SEC;
iic_mcu_write( IIC_SLA_DBG_MONITOR, 0x03, 4, &str );
}
}
*/
}
#endif
#if 0 // タスクひな形
/* ========================================================
タスクひな形
======================================================== */
task_interval tsk_hina( )
{
switch ( system_status.pwr_state )
{
case ON_CHECK:
case ON_TRIG:
case ON:
case SLEEP:
case OFF_TRIG:
default:
}
return; // 毎 tic 呼ばれることになります
}
// ポインタで何かもらうのは危険な気がしてきた
/* このように使う
renge_task_immed_add( タスク関数へのポインタ );
*/
task_status_immed tski_hina( u8 * arg )
{
return ( ERR_FINISED );
// ERR_FINISED タスクを削除
// ERR_CONTINUE 次になんか割り込みなり、ユーザー操作なり、システムチックが
// 来たときに再度実行
}
#endif