mirror of
https://github.com/rvtr/ctr_mcu.git
synced 2025-06-19 00:55:37 -04:00
c1954443a6
git-svn-id: file:///Volumes/Transfer/gigaleak_20231201/2020-05-23%20-%20ctr.7z%20+%20svn_v1.068.zip/ctr/svn/ctr_mcu@153 013db118-44a6-b54f-8bf7-843cb86687b1
247 lines
7.3 KiB
C
247 lines
7.3 KiB
C
/* ========================================================
|
||
加速度センサ関係
|
||
・データ更新完了でデータを吸い上げ手レジスタを更新、CPUに割り込み
|
||
・フラグが立っていれば歩数カウント
|
||
・加速度センサ割り込みからタスクを登録して下さい。（I2Cの競合回避などがあるので）
|
||
|
||
======================================================== */
|
||
#pragma SFR
|
||
#pragma NOP
|
||
#pragma HALT
|
||
#pragma STOP
|
||
#pragma ROT
|
||
// rorb, rolb, rorw, rolw
|
||
#pragma MUL
|
||
#pragma BCD
|
||
|
||
#include "incs.h"
|
||
#include <math.h>
|
||
|
||
// ========================================================
|
||
// レジスタ名
|
||
#define ACC_REG_WHOAMI 0x0F
|
||
#define ACC_REG_CTRL1 0x20
|
||
#define ACC_REG_CTRL5 0x24
|
||
#define ACC_REG_X 0x28
|
||
|
||
// ビット位置
|
||
#define ACC_bP_PM0 5
|
||
#define ACC_bP_DR0 3
|
||
|
||
// ビット設定値
|
||
#define ACC_BITS_PM_PDN 0
|
||
#define ACC_BITS_PM_NORM 1
|
||
#define ACC_BITS_PM_LP0R5 2
|
||
#define ACC_BITS_PM_LP1 3
|
||
#define ACC_BITS_PM_LP2 4
|
||
#define ACC_BITS_PM_LP5 5
|
||
#define ACC_BITS_PM_LP10 6
|
||
|
||
#define ACC_BITS_DR_50Hz 0
|
||
#define ACC_BITS_DR_100Hz 1
|
||
#define ACC_BITS_DR_400Hz 2
|
||
#define ACC_BITS_DR_1000Hz 3
|
||
|
||
#define ACC_BITS_ALL_AXIS_ON 7
|
||
|
||
|
||
#define VREG_BITMASK_ACC_CONF_ACQ ( 1 << 0 )
|
||
#define VREG_BITMASK_ACC_CONF_HOSU ( 1 << 1 )
|
||
|
||
|
||
|
||
|
||
// ========================================================
|
||
task_status tsk_soft_int( );
|
||
|
||
|
||
|
||
/* ========================================================
|
||
・割り込みを確認してデータを吸い上げ、レジスタに書き出します
|
||
・本当であればコールバック関数を登録しておけばいいじゃんとなるのですが、
|
||
I2Cが使用中だったら？とか考えると私ではそこまでできないのです。
|
||
・自動歩数計とかでも結局
|
||
======================================================== */
|
||
task_status_immed tsk_cbk_accero( )
|
||
{ // （疑似）isrから登録されます
|
||
|
||
/*
|
||
if(( system_status.pwr_state == OFF ) || ( system_status.pwr_state == BT_CHARGE ) )
|
||
{
|
||
return ( ERR_SUCCESS );
|
||
}
|
||
else
|
||
{
|
||
*/
|
||
// 加速度センサデータレジスタへの反映
|
||
if( iic_mcu_read( IIC_SLA_ACCEL, ( ACC_REG_X | 0x80 ), 6, &vreg_ctr[VREG_C_ACC_XL] )
|
||
!= ERR_SUCCESS )
|
||
{
|
||
// 加速度センサが異常になったので止める
|
||
vreg_ctr[VREG_C_ACC_CONFIG] &= ~( VREG_BITMASK_ACC_CONF_HOSU | VREG_BITMASK_ACC_CONF_ACQ );
|
||
// vreg_ctr[ VREG_C_STATUS_1 ] |= REG_BIT_ACCERO_ERR;
|
||
acc_hosu_set();
|
||
return ( ERR_SUCCESS ); // タスクの削除は必要
|
||
}
|
||
else
|
||
{
|
||
// 正常時パス //
|
||
// 加速度更新＆割り込み
|
||
if( (( vreg_ctr[VREG_C_ACC_CONFIG] & VREG_BITMASK_ACC_CONF_ACQ ) != 0 ) &&
|
||
( system_status.pwr_state == ON )
|
||
)
|
||
{
|
||
set_irq( VREG_C_IRQ1, REG_BIT_ACC_DAT_RDY );
|
||
// ゴミデータのカラ読み
|
||
if( ACC_VALID == 1 )
|
||
{
|
||
u8 temp[6];
|
||
iic_mcu_read( IIC_SLA_ACCEL, ( ACC_REG_X | 0x80 ), 6, temp );
|
||
}
|
||
}
|
||
if(( system_status.pwr_state != OFF ) &&
|
||
( system_status.pwr_state != BT_CHARGE ) &&
|
||
( ( vreg_ctr[VREG_C_ACC_CONFIG] & VREG_BITMASK_ACC_CONF_HOSU ) != 0 )
|
||
)
|
||
{
|
||
DBG_LED_WIFI_2_on;
|
||
pedometer(); // 歩数計
|
||
DBG_LED_WIFI_2_off;
|
||
}
|
||
}
|
||
return ( ERR_SUCCESS );
|
||
}
|
||
|
||
|
||
|
||
|
||
|
||
/*=======================================================
|
||
加速度センサ透過アクセス リード
|
||
========================================================*/
|
||
task_status_immed acc_read( )
|
||
{
|
||
vreg_ctr[VREG_C_ACC_W_BUF] = iic_mcu_read_a_byte( IIC_SLA_ACCEL, vreg_ctr[VREG_C_ACC_R_ADRS] );
|
||
// vreg_ctr[ VREG_C_ACC_R_BUF ] = iic_mcu_read_a_byte( IIC_SLA_ACCEL, vreg_ctr[VREG_C_ACC_R_ADRS] );
|
||
vreg_ctr[VREG_C_IRQ1] |= REG_BIT_ACC_ACK;
|
||
if( ( vreg_ctr[VREG_C_IRQ_MASK1] & REG_BIT_ACC_ACK ) == 0 )
|
||
{
|
||
IRQ0_ast;
|
||
}
|
||
return ( ERR_SUCCESS );
|
||
}
|
||
|
||
|
||
|
||
/*=========================================================
|
||
加速度センサ透過アクセス ライト
|
||
========================================================*/
|
||
task_status_immed acc_write( )
|
||
{
|
||
iic_mcu_write_a_byte( IIC_SLA_ACCEL, vreg_ctr[VREG_C_ACC_W_ADRS], vreg_ctr[VREG_C_ACC_W_BUF] );
|
||
vreg_ctr[VREG_C_IRQ1] |= REG_BIT_ACC_ACK;
|
||
if( ( vreg_ctr[VREG_C_IRQ_MASK1] & REG_BIT_ACC_ACK ) == 0 )
|
||
{
|
||
IRQ0_ast;
|
||
}
|
||
return ( ERR_SUCCESS );
|
||
}
|
||
|
||
|
||
|
||
/*=========================================================
|
||
自動歩数カウントモードにセット
|
||
todo 他のモードだったら止めたり、復帰させたり
|
||
割り込みルーチンなどでカウント判定が必要
|
||
========================================================*/
|
||
task_status_immed acc_hosu_set( )
|
||
{
|
||
u8 str_send_buf[4];
|
||
|
||
iic_mcu_read_a_byte( IIC_SLA_ACCEL, ACC_REG_WHOAMI );
|
||
if( iic_mcu_bus_status == ERR_NOSLAVE )
|
||
{
|
||
vreg_ctr[ VREG_C_STATUS_1 ] |= REG_BIT_ACCERO_ERR;
|
||
#ifdef _MCU_BSR_
|
||
// PMK23 = 1;
|
||
#endif
|
||
return ( ERR_SUCCESS ); // とりあえず、タスクは削除しなくてはならない
|
||
}else{
|
||
vreg_ctr[ VREG_C_STATUS_1 ] &= ~REG_BIT_ACCERO_ERR;
|
||
}
|
||
|
||
|
||
str_send_buf[1] = 0x00; // ctrl2 HPF:normal, filterd, HPF for IRQ : dis/dis, HPF coeff:norm
|
||
#ifdef _MODEL_WM0_
|
||
str_send_buf[2] = 0x10; // 3 IRQ pol :Active HI, Drive:Pushpull,
|
||
/// IRQ2flg latch: auto clear after read, IRQ2 conf: IRQ( fall,shock,...)
|
||
/// 1 : auto clear after read, conf: data ready
|
||
#else
|
||
# ifdef _MODEL_CTR_JIKKI_
|
||
str_send_buf[2] = 0x10;
|
||
# else
|
||
str_send_buf[2] = 0x02; // 3 IRQ pol :Active HI, Drive:Pushpull,
|
||
/// IRQ2flg latch: auto clear after read, IRQ2 conf: IRQ( fall,shock,...)
|
||
/// 1 : auto clear after read, conf: data ready
|
||
# endif
|
||
#endif
|
||
|
||
str_send_buf[3] = 0x80; // ctrl3 block update:enable, MSB first, scale: +-2G(default), selftest: dis
|
||
|
||
if( ( vreg_ctr[VREG_C_ACC_CONFIG] &
|
||
( VREG_BITMASK_ACC_CONF_HOSU | VREG_BITMASK_ACC_CONF_ACQ ) ) == 0 )
|
||
{
|
||
#ifdef _MCU_BSR_
|
||
PMK23 = 1;
|
||
#endif
|
||
// 完全停止
|
||
str_send_buf[0] =
|
||
( ACC_BITS_PM_PDN << ACC_bP_PM0 | 0 << ACC_bP_DR0 | ACC_BITS_ALL_AXIS_ON );
|
||
}
|
||
else
|
||
{
|
||
#ifdef _MCU_BSR_
|
||
PMK23 = 0;
|
||
#endif
|
||
// 100Hz 自動取り込み
|
||
str_send_buf[0] =
|
||
( ACC_BITS_PM_NORM << ACC_bP_PM0
|
||
| ACC_BITS_DR_100Hz << ACC_bP_DR0
|
||
| ACC_BITS_ALL_AXIS_ON );
|
||
}
|
||
iic_mcu_write( IIC_SLA_ACCEL, ( ACC_REG_CTRL1 | 0x80 ), 4, str_send_buf );
|
||
|
||
// カラ読み
|
||
if( ACC_VALID == 1 )
|
||
{
|
||
if( system_status.pwr_state == ON )
|
||
{
|
||
u8 temp[6];
|
||
iic_mcu_read( IIC_SLA_ACCEL, ( ACC_REG_X | 0x80 ), 6, temp );
|
||
}
|
||
}
|
||
return ( ERR_SUCCESS );
|
||
}
|
||
|
||
|
||
|
||
/* ========================================================
|
||
加速度センサ割り込み
|
||
I2Cが使用中かもしれないので、読み出しタスクの登録を行うのみ
|
||
======================================================== */
|
||
__interrupt void intp23_ACC_ready( )
|
||
{
|
||
EI();
|
||
if( ( vreg_ctr[VREG_C_ACC_CONFIG] & 0x03 ) != 0x00 )
|
||
{
|
||
if( ( system_status.pwr_state == ON ) || ( system_status.pwr_state == SLEEP ) )
|
||
{
|
||
if( ACC_VALID )
|
||
{
|
||
renge_task_immed_add( tsk_cbk_accero );
|
||
}
|
||
}
|
||
}
|
||
}
|
||
|