#ifndef __PM__
#define __PM__


#define IIC_SLA_PMIC              0x84
#define IIC_SLA_BT_GAUGE          0x6C

#define VCOM_DEFAULT_T  92
#define VCOM_DEFAULT_B  95

//=========================================================
enum PMIC_REG_ADRS
{
  PM_REG_ADRS_VER = 0x00,       // verinfo など
  PM_REG_ADRS_VDD_SYS,          // システムが使用する電源
  PM_REG_ADRS_VDD_LCD,          // 液晶電源
  PM_REG_ADRS_CONT,             // /RESET1, LoadSwitch
  PM_REG_ADRS_BL,               // バックライト on/off
  PM_REG_ADRS_POW_SAVE,         // 省電力設定
  PM_REG_ADRS_POW_DAC1,
  PM_REG_ADRS_POW_DAC2
};

enum BT_GAUGE_REG_ADRS
{
  BT_GAUGE_REG_VCELL    = 0x02,    // それぞれ16ビットのため
  BT_GAUGE_REG_SOC      = 0x04,
  BT_GAUGE_REG_MODE     = 0x06,
  BT_GAUGE_REG_VERSION  = 0x08,
  BT_GAUGE_REG_OCV      = 0x0E,
  BT_GAUGE_REG_RCOMP    = 0x0C,
  BT_GAUGE_REG_LOCK     = 0x3E,
  BT_GAUGE_REG_BT_PARAM = 0x40,
  BT_GAUGE_REG_COMMAND  = 0xFE
};

enum BT_VENDER
{
    BT_VENDER_SHIROBAKO = 0,
    BT_VENDER_PANA   = 3,
    BT_VENDER_MAXELL = 7
};


//=========================================================
// CODEC上のPMIC互換レジスタ
#define CODEC_REG_PM 0x10
#define CODEC_REG_BL 0x11
#define CODEC_REG_BT 0x12
//#define CODEC_REG_VOL 0x13   // ...都合により、adc.hで定義

// TWLがSPIでPMICに投げたコマンド
#define REG_BIT_TWL_REQ_OFF_REQ  ( 1 << 6 )
#define REG_BIT_TWL_REQ_RST_REQ  ( 1 << 0 )
#define REG_BIT_TWL_REQ_BL       ( 3 << 2 )




// 0x03 pw cnt3
#define PM_REG_BIT_LDSW      ( 1 << 0 )
#define PM_REG_BIT_nRST1     ( 1 << 1 )

// 0x01 pw cnt1
#define PM_REG_BIT_VDD        0x0F
#define PM_REG_BIT_VDD50A    ( 1 << 4 )

// 0x02 pw cnt2
#define PM_REG_BIT_VDDLCD      0x07
#define PM_REG_BIT_LCD_VCS   ( 0x01 << 4 )
#define PM_REG_BIT_LCD_TCOM  ( 0x01 << 3 )

// 0x04 bl cnt
#define PM_REG_BIT_BL_U         0x01
#define PM_REG_BIT_BL_L         0x02


// 0x05 pow save
#define PM_REG_BIT_VDD1P_1R15   0b00000000
#define PM_REG_BIT_VDD1P_1R05   0b00001000
#define PM_REG_BIT_VDD1P_0R90   0b00100000
#define PM_REG_BIT_VDD_AUTO     0b00000111
#define PM_REG_BIT_VDD_PWM      0b00000000


#define DELAY_PM_TW_PWUP               16
#define DELAY_PM_TSS_50B_AND_TCOM      17
#define DELAY_PM_5V_TO_TCOM            17
#define DELAY_PM_TCOM_TO_VCS           3
#define DELAY_PM_VCS_TO_BL             ( 17 + 5 )
#define DELAY_PM_LCD_OFF               ( 50 + 1 )


//=========================================================
extern u8 raw_adc_temperature;


//=========================================================
err PM_sys_pow_on(  );
err PM_sys_pow_off(  );
err PM_bt_auth(  );
void PM_init(  );
err PM_LCD_vcom_set(  );

err PM_LCD_on(  );
void PM_LCD_off(  );
err PM_BL_set( u8 );

task_status_immed PM_bt_temp_update(  );
task_status_immed tski_vcom_set(  );
task_status_immed tski_PM_LCD_on();
task_status_immed tski_PM_LCD_off();
task_status_immed tski_PM_BL_set();


//  　これを呼ぶ前に、現在温度を教えておく必要があります。
#define PM_reset()     ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT, 0x00 ) )


//=========================================================


// 元栓 //
#define PM_LDSW_on()   ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT, PM_REG_BIT_LDSW ))
#define PM_LDSW_off()  ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT, 0 ))


// システム電源 //
#define PM_VDD_on()    ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_SYS, PM_REG_BIT_VDD ))
#define PM_VDD50A_on() ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_SYS, ( PM_REG_BIT_VDD | PM_REG_BIT_VDD50A )))
#define PM_VDD_off()   ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_SYS, 0 ))
#define PM_off()       ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_SYS, 0 ))

#ifdef _MODEL_CTR_
#define PM_VDD_normMode()   ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_SAVE, PM_REG_BIT_VDD1P_1R15 | PM_REG_BIT_VDD_PWM ))
#define PM_VDD_ecoMode()    ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_SAVE, PM_REG_BIT_VDD1P_0R90 | PM_REG_BIT_VDD_AUTO ))

#else
// 本番チップ待ち
#ifdef _PM_BUG_
#define PM_VDD_ecoMode()    ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_SAVE, PM_REG_BIT_VDD1P_0R90 | PM_REG_BIT_VDD_AUTO ))
#define PM_VDD_normMode()   ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_SAVE, PM_REG_BIT_VDD1P_1R10 | PM_REG_BIT_VDD_PWM ))

#else
#define PM_VDD_ecoMode()    ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_SAVE, PM_REG_BIT_VDD1P_1R05 | PM_REG_BIT_VDD_AUTO ))
#define PM_VDD_normMode()   ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_SAVE, PM_REG_BIT_VDD1P_1R05 | PM_REG_BIT_VDD_PWM ))

#endif
#endif

// ほか //
#ifdef _PMIC_TWL_
#define PM_reset_neg() { PM0.0 = 1; }
#define PM_reset_ast() { P0.0  = 0; PM0.0 = 0; }
#define PM_chk_LDSW()  ( 1 )
#else

#define PM_reset_neg() ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT, ( PM_REG_BIT_LDSW | PM_REG_BIT_nRST1 )))
#define PM_reset_ast() ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT, ( PM_REG_BIT_LDSW )))
#define PM_chk_LDSW()  ( iic_mcu_read_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT ) & PM_REG_BIT_LDSW )
// ↑ 0 だと異常
#endif


// 液晶系電源 //
#define PM_VDDLCD_on() ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_LCD, PM_REG_BIT_VDDLCD ))
#define PM_TCOM_on()   ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_LCD, ( PM_REG_BIT_VDDLCD | PM_REG_BIT_LCD_TCOM )))
#define PM_VCS_on()    ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_LCD, ( PM_REG_BIT_VDDLCD | PM_REG_BIT_LCD_VCS | PM_REG_BIT_LCD_TCOM )))
#define PM_TCOM_VCS_off() PM_VDDLCD_on()
#define PM_VDDLCD_off() ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_LCD, 0 ) )

#define PM_set_BL( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_BL, dat ) )
#define PM_set_adc1( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_DAC1, dat ) )
#define PM_set_adc2( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_DAC2, dat ) )


#endif // __PM__