git-svn-id: file:///Volumes/Transfer/gigaleak_20231201/2020-05-23%20-%20ctr.7z%20+%20svn_v1.068.zip/ctr/svn/ctr_mcu@28 013db118-44a6-b54f-8bf7-843cb86687b1

trunk/accero.c

@@ -49,7 +49,8 @@
 #define VREG_BITMASK_ACC_CONF_ACQ  ( 1 << 0 )
 
 // ========================================================
-static u16 hyst_pedometer[256];
+extern u8 pool[];
+u16* hyst_pedometer;
 
 
 // ========================================================
@@ -72,100 +73,6 @@ task_status_immed tsk_cbk_accero(  )
         // 加速度センサデータレジスタへの反映
         iic_mcu_read( IIC_SLA_ACCEL, ( ACC_REG_X | 0x80 ), 6, &vreg_ctr[VREG_C_ACC_XL] );
 
-        {
-            // 歩数計 //
-            unsigned int mean;          // 二乗平均はあまりにも処理が重いので(!) 絶対値の合計にします
-            static u8 direction;
-
-            static s16 th_H = 0x2380;   // 閾値。暫定。動的変更とかしたい…
-            static s16 th_L = 0x2180;
-
-            static u16 interval;        // 山と谷の間の時間。短すぎても長すぎてもはじく。
-
-
-            s16 sx16 = vreg_ctr[VREG_C_ACC_XH] * 256 + vreg_ctr[VREG_C_ACC_XL];
-            s16 sy16 = vreg_ctr[VREG_C_ACC_YH] * 256 + vreg_ctr[VREG_C_ACC_YL];
-            s16 sz16 = vreg_ctr[VREG_C_ACC_ZH] * 256 + vreg_ctr[VREG_C_ACC_ZL];
-
-            // そのうちローコストな方法を考え
-            mean = sqrt( (long)abs( sx16 ) * abs( sx16 ) /4 +
-                         (long)abs( sy16 ) * abs( sy16 ) /4 +
-                         (long)abs( sz16 ) * abs( sz16 ) /4 );
-
-            {
-                static u8 count_H = 0;
-                static u8 count_L = 0;
-
-                if( direction == 0 ) // 前回に下限を下回っていて
-                {
-                    if( mean > th_H ) // 今回、上の閾値を上回った
-                    {
-                        if( count_H == 5 ){  // 突発的なノイズは省く...
-                            direction = 1;
-                            count_L = 0;
-                        }
-                        if( count_H <= 5 ){
-                            count_H += 1;
-                        }
-                    }
-                    else
-                    {
-                        count_H = 0;
-                    }
-                }
-
-                if( count_H >= 5 ){
-                    interval += 1;
-                }
-                if( 500 < interval ){
-                    interval = 0;
-                    direction = 0;
-                    count_H = 0;
-                    count_L = 0;
-                }
-
-                // 下の閾値を超えるのを待つ
-                if( direction == 1 )
-                {
-                    if( mean < th_L )
-                    {
-                        if( count_L == 5 ){
-                            direction = 0; // 次は上の閾値を待つ
-                            if( count_H >= 5 ){
-                                if( 70 < interval )
-                                {
-                                    vreg_ctr[ VREG_C_ACC_HOSU_L ] += 1; // 一歩加算
-                                    hyst_pedometer[0] += 1;
-                                }
-                            }
-                            count_H = 0;
-                        }
-                        if( count_L <= 5 ){
-                            count_L += 1;
-                        }
-                    }
-                    else
-                    {
-                        count_L = 0;
-                    }
-                }
-            }
-
-            // debug
-            if( mean > th_H )
-            {
-                DBG_LED_WIFI_on;
-                DBG_LED_WIFI_2_off;
-            }
-
-            if( mean < th_L )
-            {
-                DBG_LED_WIFI_off;
-                DBG_LED_WIFI_2_on;
-            }
-
-        }
-
 
         if( ( vreg_ctr[VREG_C_ACC_CONFIG] &
               ( VREG_BITMASK_ACC_CONF_ACQ | VREG_BITMASK_ACC_CONF_HOSU ) ) != 0 )
@@ -174,16 +81,61 @@ task_status_immed tsk_cbk_accero(  )
         }
     }
 
-    // 歩数計 offでなければ、電源off中でも計測
+    // 歩数計 /////////////////////////////////////////////
-    if( ( vreg_ctr[VREG_C_ACC_CONFIG] & VREG_BITMASK_ACC_CONF_HOSU ) != 0x00 )
+    // offでなければ、電源off中でも計測
+//    if( ( vreg_ctr[VREG_C_ACC_CONFIG] & VREG_BITMASK_ACC_CONF_HOSU ) != 0x00 )
+    if( 1 )
     {
-        if( ( vreg_ctr[VREG_C_ACC_CONFIG] & VREG_BITMASK_ACC_CONF_ACQ ) != 0x00 )
+            static s16 th_H = 0x3500;   // 閾値。暫定。動的変更とかしたい…
+            static s16 th_L = 0x2A00;
+            static u16 acc_norm[3];     // 加速度の大きさのヒストリ。数字が大きい方が古い
+            static u8 direction;        // (0)極大を待つか (1)極小を待つか
+            static u16 interval;        // 山と谷の間の時間。短すぎても長すぎてもはじく。
+
+        u16 sx16 = abs( (u16)vreg_ctr[VREG_C_ACC_XH] * 256 + vreg_ctr[VREG_C_ACC_XL] );
+        u16 sy16 = abs( (u16)vreg_ctr[VREG_C_ACC_YH] * 256 + vreg_ctr[VREG_C_ACC_YL] );
+        u16 sz16 = abs( (u16)vreg_ctr[VREG_C_ACC_ZH] * 256 + vreg_ctr[VREG_C_ACC_ZL] );
+
+        acc_norm[2] = acc_norm[1];
+        acc_norm[1] = acc_norm[0];
+            // そのうちローコストな方法を考える、かも
+        acc_norm[0] = sqrt( (long)sx16 * ( sx16 / 2 ) +
+                            (long)sy16 * ( sy16 / 2 ) +
+                            (long)sz16 * ( sz16 / 2 ) );
+
+        if( direction == 0 ) // 前回は谷
         {
-            // 歩数計アルゴリズム 100Hz版
+            if( acc_norm[2] <= acc_norm[1] && acc_norm[1] > acc_norm[0]
+                && acc_norm[0] > th_H ) // 極大で、閾値を超えていた
+            {
+                direction = 1; // 極小を待つ
+                interval = 0;  // 極小までの時間を計る
+            }
         }
         else
         {
-            // 同　省電力版
+            if( acc_norm[2] >= acc_norm[1] && acc_norm[1] < acc_norm[0]
+                && acc_norm[0] < th_L )
+            {
+                direction = 0;
+                if( 2 < interval && interval < 20 )  // 早すぎず、遅すぎず
+                {
+                    // 一歩加算。　いろいろ失敗した
+                    if( ++vreg_ctr[ VREG_C_ACC_HOSU_L ] == 0 )
+                    {
+                        if( ++vreg_ctr[ VREG_C_ACC_HOSU_M ] == 0 )
+                        {
+                            ++vreg_ctr[ VREG_C_ACC_HOSU_H ];
+                        }
+                    }
+                    if( ++*hyst_pedometer == 0 )
+                    {
+                        *hyst_pedometer = 65535;
+                    }
+                }
+                interval = 0;
+            }
+            interval += 1;
         }
 
     }
@@ -271,28 +223,18 @@ task_status_immed acc_hosu_set(  )
         // 完全停止
         str_send_buf[0] =
             ( ACC_BITS_PM_PDN << ACC_bP_PM0 | 0 << ACC_bP_DR0 | ACC_BITS_ALL_AXIS_ON );
+        hyst_pedometer = (u16*)pool; // 止めるとヒストリが無効になります（暫定）
     }
     else
     {
 #ifdef _MCU_BSR_
 	    PMK23 = 0;
 #endif
-        if( ( vreg_ctr[VREG_C_ACC_CONFIG] & VREG_BITMASK_ACC_CONF_ACQ ) != 0x00 )
-        {
         // 100Hz 自動取り込み
         str_send_buf[0] =
-                ( ACC_BITS_PM_NORM << ACC_bP_PM0 | ACC_BITS_DR_100Hz <<
+            ( ACC_BITS_PM_NORM << ACC_bP_PM0
-                  ACC_bP_DR0 | ACC_BITS_ALL_AXIS_ON );
+              | ACC_BITS_DR_100Hz << ACC_bP_DR0
-        }
+              | ACC_BITS_ALL_AXIS_ON );
-        else
-        {
-            // 100Hz 自動取り込み
-            str_send_buf[0] =
-                ( ACC_BITS_PM_NORM << ACC_bP_PM0 | ACC_BITS_DR_100Hz <<
-                  ACC_bP_DR0 | ACC_BITS_ALL_AXIS_ON );
-//        // 10Hz 自動取り込み(歩数計向け省電力モード)
-//        str_send_buf[0] = ( ACC_BITS_PM_LP10 << ACC_bP_PM0 | ACC_BITS_ALL_AXIS_ON );
-        }
     }
     iic_mcu_write( IIC_SLA_ACCEL, ( ACC_REG_CTRL1 | 0x80 ), 4, str_send_buf );
 

trunk/adc.c

@@ -34,13 +34,13 @@ void tsk_adc(  )
     static u8 sndvol_codec;
     static u8 bt_temp_old;
 
-    if( task_interval != system_time )
+    if( task_interval-- != 0 )
     {
         return;
     }
     else
     {
-        task_interval += (u8)( INTERVAL_TSK_ADC / SYS_INTERVAL_TICK );
+        task_interval = (u8)( INTERVAL_TSK_ADC / SYS_INTERVAL_TICK );
     }
 
 
@@ -103,27 +103,22 @@ void tsk_adc(  )
 
 
             // TUNE_LED //
-            {
             // ここで？仕様？
+            {
                 switch ( vreg_ctr[VREG_C_LED_TUNE] )
                 {
-                case ( 1 ):            // 点灯
+                case LED_TUNE_ILM_ON:
                     LED_duty_TUNE = vreg_ctr[VREG_C_LED_BRIGHT];
                     break;
 
-                case ( 2 ):            //
+                case LED_TUNE_ILM_SVR:
-                default:               // 消灯
-#ifdef _MODEL_WM0_
                     LED_duty_TUNE = vreg_ctr[VREG_C_TUNE] / 16;
-#else
-                    LED_duty_TUNE = LED_BRIGHT_MAX - vreg_ctr[VREG_C_TUNE];
-#endif
                     break;
-#if 0
+
-                default:               // 消灯
+                case LED_TUNE_ILM_OFF:
+                default:
                     LED_duty_TUNE = 0;
                     break;
-#endif
                 }
             }
 
@@ -132,12 +127,12 @@ void tsk_adc(  )
 
 
         ADCEN = 1;
-        ADM =  0b00011011;      // セレクトモード、章圧、fCLK/6 ///ここから
+        ADM =  0b00011011;      // セレクトモード、章圧、fCLK/6 ///ここから ↓
 
         ADPC = 0x06;            // ADCポートのセレクト
         ADS = ADC_SEL_TUNE;
 //    NOP();
-        ADCS = 1;               // AD開始。                     /// ここまでに、1us以上開ける
+        ADCS = 1;               // AD開始。                     /// ここまで　↑　までに1us以上開ける
 
         ADIF = 0;
         ADMK = 0;
@@ -249,11 +244,11 @@ u8 get_adc( u8 ch )
 
     ADCEN = 1;
     ADCS = 0;
-    ADM = 0b00100011;          // セレクトモード、章圧、fCLK/6 ///ここから
+    ADM = 0b00100011;          // セレクトモード、昇圧、fCLK/6  ///ここから↓
 
     ADPC = 0x06;                // ADCポートのセレクト
     ADS = ch;
-    ADCS = 1;                   // AD開始。                     /// ここまでに、1us以上開ける
+    ADCS = 1;                   // AD開始。                     /// ここまで↑　に、1us以上開ける
 
     ADMK = 0;
     while( ADIF == 0 )

trunk/config.h

@@ -3,9 +3,11 @@
 
 #define _debug_
 // #define _debug_led_
+//#define _VREG_C_NEW_
+
 
 #define MCU_VER_MAJOR    0;
-#define MCU_VER_MINOR    7;
+#define MCU_VER_MINOR    8;
 
 
 //#define _PARRADIUM_

trunk/i2c_ctr.c

@@ -94,8 +94,7 @@ __interrupt void int_iic_ctr(  )
             if( !( ( vreg_ctr[VREG_C_IRQ0] == 0 )
                    && ( vreg_ctr[VREG_C_IRQ1] == 0 )
                    && ( vreg_ctr[VREG_C_IRQ2] == 0 )
-                   && ( vreg_ctr[VREG_C_IRQ3] == 0 )
+                   && ( vreg_ctr[VREG_C_IRQ3] == 0 ) ) )
-                   && ( vreg_ctr[VREG_C_IRQ4] == 0 ) ) )
             {
                 while( !IRQ0 ){;}  // 時間稼ぎ不要かも
                 IRQ0_ast;

trunk/i2c_mcu.c

@@ -15,22 +15,38 @@
 
 
 // ========================================================
+// レジスタのビット名
+// プリフィックスbだが、一部のビット名がレジスタ名にかぶるため...
+// SMR0n
+#define bCKS0    ( 1 << 15 )
+#define bCCS0    ( 1 << 14 )
+#define bSTS0    ( 1 << 8 )
+#define bSIS0    ( 1 << 6 )
+#define bMD0n2   ( 1 << 2 )
+#define bMD0n1   ( 1 << 1 )
+#define bMD0n0   ( 1 << 0 )
+#define bSMR0n_FIXEDBIT  ( 1 << 5 )
+
 // SSR0n
 #define bit_TSF0   6
-// SIR0n
-#define PECT0      ( 1 << 1 )
-// SSR0n
 #define PEF0       ( 1 << 1 )
 
+// SIR0n
+#define PECT0      ( 1 << 1 )
+
+// SCR0n
 #define TXE0       ( 1 << 15 )
 #define RXE0       ( 1 << 14 )
 #define SLC02      4
 #define DLS02      0
 #define TSF0       ( 1 << 6 )
 
+// SOn
+#define TAUS_MASK  0b0000101100001011;
+
+// DMCn
 #define DRS        ( 1 << 6 )
 
-#define TAUS_MASK  0b0000101100001011;
 
 
 
@@ -394,6 +410,7 @@ __interrupt void int_dma1(  )
         NOP(  );
         SO0 = 0x0404 | TAUS_MASK;
     }
+    IICMK10 = 1;
     iic_mcu_busy = 0;
 }
 
@@ -402,6 +419,8 @@ __interrupt void int_dma1(  )
 /* ========================================================
   IIC MCUのバイト送出完了割り込み
   ※DMA使用時は使用されません。
+  　他の割り込み処理中でDMAの割り込みにすぐ飛ばない場合、
+  　IIC割り込みのセットが間に合わず困ることがあります。
  ======================================================== */
 __interrupt void int_iic10(  )
 {
@@ -448,7 +467,7 @@ static err iic_mcu_call_slave( u8 slave )
     iic_mcu_send_st(  );
 
 //  SIR02 = SSR02;              // NAKエラーのフラグクリア
-    if( iic_mcu_send_a_byte( slave ) != 0 )
+    if( iic_mcu_send_a_byte( slave ) != ERR_SUCCESS )
     {
         iic_mcu_send_sp(  );
         return ( ERR_NAK );     // 指定のスレーブがいない / busy
@@ -465,7 +484,7 @@ static err iic_mcu_call_slave( u8 slave )
  ======================================================== */
 static err iic_mcu_send_a_byte( u8 dat )
 {
-
+    IICMK10 = 1;
     IICIF10 = 0;
     SIO10 = dat;
     while( IICIF10 == 0 )
@@ -553,6 +572,8 @@ static void iic_mcu_send_sp(  )
 void iic_mcu_start(  )
 {
     DST1 = 0;
+    NOP(  );                    // 2clkもしくは、DSTn==0をポーリング
+    NOP(  );
     DEN1 = 0;
     I2C_PU = 1;
     SAU0EN = 1;
@@ -561,13 +582,14 @@ void iic_mcu_start(  )
     NOP(  );
     NOP(  );
     SPS0 = 0x0000;              // シリアルユニットのクロック０。(8M/2)/1
-    SMR02 = 0 << 15 | 0 << 14 | 0 << 7 | 0 << 5 | 1 << 4 | 1 << 2;      // I2Cとそのクロックなど設定
+    SMR02 = bSMR0n_FIXEDBIT | bMD0n2;	// I2Cとそのクロックなど設定
     SDR02 = 5 << 9;             // ボーレート設定 (8M/2)/1/(x+1)/2
 
     SO0 = 0x0404 | TAUS_MASK;   // 最初はHH
     iic_mcu_busy = 0;
     iic_mcu_wo_dma = 0;
 
+
     // バスのリセット
     IICIF10 = 0;
     IICMK10 = 1;

trunk/led.c

@@ -12,8 +12,8 @@
 
 // ========================================================
 // TPS0
-#define BIT_PRS01             4
+#define BIT_PRS012             ( 1 << 2 )
-#define BIT_PRS00             0
+#define BIT_PRS002             ( 1 << 6 )
 
 // TMR0
 #define BIT_CKS0             15
@@ -50,7 +50,7 @@ void LED_init(  )
   　　　　　　　　７　電源 Ｈ
  */
     TAU0EN = 1;
-    TPS0 = 1 << BIT_PRS01 | 1 << BIT_PRS00;     // ƒ}ƒXƒ^<5E>[ƒNƒ<4E>ƒbƒN‚ÍCK01,8M/2/2^4 = 250kHz
+    TPS0 = BIT_PRS012 | BIT_PRS002;     // ƒ}ƒXƒ^<5E>[ƒNƒ<4E>ƒbƒN‚ÍCK01,8M/2 /2^4 = 250kHz
 
     TMR00 =
         1 << BIT_CKS0 | 0 << BIT_CCS0 | 1 << BIT_MASTER0 | 0 << BIT_STS0 | 0
@@ -310,7 +310,7 @@ void tsk_led_wifi(  )
     static u8 flag_wifi_TX;
 
 
-    if( task_interval != system_time )
+    if( task_interval-- != 0 )
     {
         return;
     }
@@ -371,7 +371,7 @@ void tsk_led_wifi(  )
                 state_wifi_tx = 0;
                 flag_wifi_TX -= 1;
             }
-            task_interval += 22;
+            task_interval = 22;
             return;
 
         }
@@ -379,7 +379,7 @@ void tsk_led_wifi(  )
         {
             LED_duty_WiFi = vreg_ctr[VREG_C_LED_BRIGHT];
             LED_WIFI_2 = 1;
-            task_interval += 200;
+            task_interval = 200;
             return;
         }
         break;
@@ -402,7 +402,7 @@ void tsk_led_wifi(  )
         {
             state_wifi_tx = 0;
         }
-        task_interval += 50;
+        task_interval = 50;
         return;
 
     case ( WIFI_LED_PTN1 ):
@@ -415,7 +415,7 @@ void tsk_led_wifi(  )
             {
                 LED_duty_WiFi = 0;
                 remain_wifi_tx = 0;
-                task_interval += MSG_SPD;
+                task_interval = MSG_SPD;
                 return;
             }
 
@@ -427,26 +427,26 @@ void tsk_led_wifi(  )
             case ( 0b00000000 ):
                 LED_duty_WiFi = 0;
                 remain_wifi_tx = 0;
-                task_interval += ( MSG_SPD * 3 );
+                task_interval = ( MSG_SPD * 3 );
                 break;
 
             case ( 0b01000000 ):
             default:
                 LED_duty_WiFi = 0;
                 remain_wifi_tx = 1;
-                task_interval += ( MSG_SPD );
+                task_interval = ( MSG_SPD );
                 break;
 
             case ( 0b10000000 ):
                 LED_duty_WiFi = vreg_ctr[VREG_C_LED_BRIGHT];
                 remain_wifi_tx = 1;
-                task_interval += ( MSG_SPD );
+                task_interval = ( MSG_SPD );
                 break;
 
             case ( 0b11000000 ):
                 LED_duty_WiFi = vreg_ctr[VREG_C_LED_BRIGHT];
                 remain_wifi_tx = 1;
-                task_interval += ( MSG_SPD * 3 );
+                task_interval = ( MSG_SPD * 3 );
                 break;
             }
             return;
@@ -469,7 +469,7 @@ void tsk_led_cam(  )
     static u8 task_interval;
     static u8 state_led_cam_twl;
 
-    if( task_interval != system_time )
+    if( task_interval-- != 0 )
     {
         return;
     }
@@ -499,7 +499,7 @@ void tsk_led_cam(  )
             LED_duty_CAM = 0;
             state_led_cam = 0;
         }
-        task_interval += 250;
+        task_interval = 250;
         break;
 
     case ( CAM_LED_ON_PLUSE ):
@@ -507,7 +507,7 @@ void tsk_led_cam(  )
         {
             LED_duty_CAM = vreg_ctr[VREG_C_LED_BRIGHT];
             state_led_cam = 1;
-            task_interval += 250;
+            task_interval = 250;
         }
         else
         {
@@ -520,7 +520,7 @@ void tsk_led_cam(  )
         {
             LED_duty_CAM = 0;
             state_led_cam = 1;
-            task_interval += 250;
+            task_interval = 250;
         }
         else
         {
@@ -546,7 +546,7 @@ void tsk_led_cam(  )
                     LED_duty_CAM = 0;
                     state_led_cam = 0;
                 }
-                task_interval += 250;
+                task_interval = 250;
                 break;
 
           case( TWL_CAMLED_ON ):

trunk/led.h

@@ -38,6 +38,13 @@ enum LED_ILUM_MODE
 };
 
 
+enum LED_MODE_TUNE
+{
+  LED_TUNE_ILM_OFF = 0,
+  LED_TUNE_ILM_ON,
+  LED_TUNE_ILM_SVR
+};
+
 // ====================================
 void LED_init(  );
 void LED_stop(  );

trunk/loader.c

@@ -357,8 +357,8 @@ void hdwinit2(  )
 #endif
 
   /*--- クロック出力/ブザー出力停止 ---*/
-    CKS0 = 0b0000000;
+    CKS0 = 0b00000000;
-    CKS1 = 0b0000000;
+    CKS1 = 0b00000000;
 
   /*--- ADCの動作停止 ---*/
     ADCEN = 0;                  /* ADCへのクロック供給停止 */

trunk/pm.c

@@ -14,7 +14,7 @@
 
 
 // ========================================================
-u8 command_bl_set;
+
 
 
 
@@ -45,6 +45,13 @@ u8        rcomp;
 float     temp_co_up;
 float     temp_co_dn;
 
+u8 command_bl_set;
+
+
+// ========================================================
+static void PM_get_batt_left();
+
+
 
 
 /******************************************************//**
@@ -79,27 +86,27 @@ void PM_init(  )
 
     // 0. バッテリ残量IC クイックスタート
     dat_16._u16 = swap_endian_16( 0x4000 ); // quick start
-    if( iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_MODE, 2, &dat_16.chars.lsb ) != ERR_SUCCESS )
+    if( iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_MODE, 2, &dat_16 ) != ERR_SUCCESS )
     {
-        vreg_ctr[ VREG_C_STATUS_1 ] |= 0x01;
+        vreg_ctr[ VREG_C_STATUS_1 ] |= REG_BIT_GASGAUGE_ERR;
     }
     else
     {
 
         // 1. ロック解除
         dat_16._u16 = swap_endian_16( 0x4057 ); // unlock key
-        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_LOCK, 2, &dat_16._u16 );
+        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_LOCK, 2, &dat_16 );
 
         // 2. 初期パラメータを一時保存
         iic_mcu_read( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_RCOMP, 4, origParam );
 
         // 3. 一時的にOCVを変更
         dat_16._u16 = swap_endian_16( 0xD4C0 ); // マジックナンバー的なもの。メーカー指定
-        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_OCV, 2, &dat_16._u16 );
+        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_OCV, 2, &dat_16 );
 
         // 4. 一時的にRCOMPを変更
         dat_16._u16 = swap_endian_16( 0xFF00 );
-        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_RCOMP, 2, &dat_16._u16 );
+        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_RCOMP, 2, &dat_16 );
 
         // 電池メーカーの識別
         BT_DET_P = 1;
@@ -124,7 +131,7 @@ void PM_init(  )
 
         // 7. OCVに「とある値」を書く
         dat_16._u16 = swap_endian_16( 0xD4C0 );
-        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_OCV, 2, &dat_16._u16 );
+        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_OCV, 2, &dat_16 );
 
         // 8. 150～600ms待つ。600msは厳守
         wait_ms( 200 );
@@ -143,7 +150,7 @@ void PM_init(  )
 
         // 11. ロック
         dat_16._u16 = swap_endian_16( 0x0000 ); // lock key
-        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_LOCK, 2, &dat_16._u16 );
+        iic_mcu_write( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_LOCK, 2, &dat_16 );
 
         // おしまい //
     }
@@ -246,25 +253,42 @@ err PM_LCD_off(  )
     return ( ERR_SUCCESS );
 }
 
+err PM_BL_on(  )
+{
+    wait_ms( 10 );
+    vreg_ctr[VREG_C_STATUS] |= REG_BIT_BL;
+    return ( PM_chk_LDSW(  ) );
+}
+
+err PM_BL_off(  )
+{
+    vreg_ctr[VREG_C_STATUS] &= ~REG_BIT_BL;
+    return ( ERR_SUCCESS );
+}
+
+
 err PM_BL_set(  )
 {
     // 何もしない
     wait_ms( 10 );
+#ifdef _VREG_C_NEW_
         vreg_ctr[VREG_C_STATUS] = ( vreg_ctr[VREG_C_STATUS] & ~( REG_BIT_BL_U | REG_BIT_BL_L )
         | ( command_bl_set & REG_BIT_CMD_BL_U_ON )? REG_BIT_BL_U
         | ( command_bl_set & REG_BIT_CMD_BL_L_ON )? REG_BIT_BL_L
         );
-    return ( ERR_SUCCESS );
+#else
+    vreg_ctr[VREG_C_STATUS] |= REG_BIT_BL;
+#endif
+    return ( PM_chk_LDSW(  ) );
 }
 
+
 err PM_LCD_vcom_set(  )
 {
-    // 何もしない
     return ( ERR_SUCCESS );
 }
 
 
-
 #else
 # ifdef _PARRADIUM_
 // パラディウム上のSoCでチェックしたいとき、PMICも液晶もつながってないので
@@ -285,13 +309,32 @@ err PM_LCD_off(  )
 }
 
 
+err PM_BL_on(  )
+{
+    vreg_ctr[VREG_C_STATUS] |= REG_BIT_BL;
+    return ( ERR_SUCCESS );
+}
+
+
+err PM_BL_off(  )
+{
+    vreg_ctr[VREG_C_STATUS] &= ~REG_BIT_BL;
+    return ( ERR_SUCCESS );
+}
+
+
 err PM_BL_set(  )
 {
-    vreg_ctr[VREG_C_STATUS] = ( vreg_ctr[VREG_C_STATUS] & ~( REG_BIT_BL_U | REG_BIT_BL_L )
+    wait_ms( 10 );
+#ifdef _VREG_C_NEW_
         vreg_ctr[VREG_C_STATUS] = ( vreg_ctr[VREG_C_STATUS] & ~( REG_BIT_BL_U | REG_BIT_BL_L )
         | ( command_bl_set & REG_BIT_CMD_BL_U_ON )? REG_BIT_BL_U
         | ( command_bl_set & REG_BIT_CMD_BL_L_ON )? REG_BIT_BL_L
-    return ( ERR_SUCCESS );
+        );
+#else
+    vreg_ctr[VREG_C_STATUS] |= REG_BIT_BL;
+#endif
+    return ( PM_chk_LDSW(  ) );
 }
 
 
@@ -301,6 +344,10 @@ err PM_LCD_vcom_set(  )
 }
 
 
+
+
+
+
 # else
 // PMIC CTR
 
@@ -347,14 +394,33 @@ err PM_LCD_off(  )
 }
 
 
+
+err PM_BL_on(  )
+{
+    PM_set_BL( 0x03 );
+    wait_ms( 10 );
+
+    vreg_ctr[VREG_C_STATUS] |= REG_BIT_BL;
+    return ( PM_chk_LDSW(  ) );
+}
+
+
+
+err PM_BL_off(  )
+{
+    PM_set_BL( 0x00 );
+    vreg_ctr[VREG_C_STATUS] &= ~REG_BIT_BL;
+    return ( ERR_SUCCESS );
+}
+
+
+
 /* ========================================================
 　バックライトの個別on/off
 　現状から　on/off/維持　のフラグなので面倒
 ======================================================== */
 err PM_BL_set(  )
 {
-    u8 temp;
-
     // まじめにRMW
     //    temp = iic_mcu_read_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_BL );
 
@@ -435,6 +501,18 @@ task_status_immed tski_PM_LCD_off(  )
     return ( ERR_FINISED );
 }
 
+task_status_immed tski_PM_BL_on(  )
+{
+    PM_BL_on(  );
+    return ( ERR_FINISED );
+}
+
+task_status_immed tski_PM_BL_off(  )
+{
+    PM_BL_off(  );
+    return ( ERR_FINISED );
+}
+
 task_status_immed tski_PM_BL_set(  )
 {
     PM_BL_set(  );
@@ -446,7 +524,6 @@ task_status_immed tski_PM_BL_set(  )
 
 
 
-
 /* ========================================================
   シーケンスの通り電源を立ち上げてゆきます。
   返値 0 最後まで正常に完了した。
@@ -470,8 +547,7 @@ err PM_sys_pow_on(  )
     PM_bt_temp_update(  );      // 温度のtemp。　残量ICに行きます
 
     // 残量チェック
-    vreg_ctr[VREG_C_BT_REMAIN] = PM_get_batt_left(  );
+    PM_get_batt_left();         // 先に、PM_init()が実行されている必要があります。(大丈夫)
-    vreg_ctr[VREG_C_BT_REMAIN] = 99;
     if( vreg_ctr[VREG_C_BT_REMAIN] < 0 )
     {
         return ( 1 );
@@ -521,8 +597,7 @@ err PM_sys_pow_on(  )
 
 
     // 残量確認
-    temp = PM_get_batt_left(  );
+    temp = 99;
-    temp = 200;
     if( temp < ( 255 * 0.03 ) )
     {
         return ( ERR_ERR );
@@ -611,14 +686,13 @@ void tsk_batt(  )
     static u8 task_interval = 0;
     static u8 charge_hys = 0;   // ヒステリシスで上限下限を拡張するとき１
 
-    if( task_interval != 0 )
+    if( task_interval-- != 0 )
     {
-        task_interval -= 1;
         return;
     }
     else
     {
-        task_interval = ( INTERVAL_TSK_BATT / SYS_INTERVAL_TICK );
+        task_interval = (u8)( INTERVAL_TSK_BATT / SYS_INTERVAL_TICK );
     }
 
     // 電源周りのステータスが変化？ ///
@@ -663,18 +737,8 @@ void tsk_batt(  )
     // 充電LED
     LED_duty_CHARGE = !BT_CHG_n ? vreg_ctr[VREG_C_LED_BRIGHT] : 0;
 
-    if(( vreg_ctr[ VREG_C_STATUS_1 ] & REG_BIT_GASGAUGE_ERR ) == 0 )
+    // 電池残量
-    {
+    PM_get_batt_left();
-        {
-            // 電池残量の取得 //
-            iic_mcu_read( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_VCELL, 2, &vreg_ctr[ VREG_C_BT_REMAIN ] );
-            // todo 閾値を超えたら割り込み
-        }
-    }
-    else
-    {
-        vreg_ctr[ VREG_C_BT_REMAIN ] = 99;
-    }
 
     // PMIC-NTRに電池残量を教えてあげる
     if( vreg_ctr[ VREG_C_BT_REMAIN ] < 5 )
@@ -686,9 +750,7 @@ void tsk_batt(  )
         iic_mcu_write_a_byte( IIC_SLA_CODEC, CODEC_REG_BT, 0 );
     }
 
-
+    // dubug monitor
-
-
     vreg_ctr[ VREG_C_FREE0 ] = vreg_ctr[ VREG_C_BT_REMAIN ];
     vreg_ctr[ VREG_C_FREE1 ] = iic_mcu_read_a_byte( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_VCELL );
 
@@ -746,27 +808,18 @@ task_status_immed ntr_pmic_comm(  )
     {
         return ( ERR_FINISED );
     }
-
     DI(  );
 
-    // バックライト 上 がどうかした
+#ifdef _VREG_C_NEW_
     if( ( ( reg1_old ^ reg_shadow ) & REG_BIT_TWL_REQ_BL_U ) != 0 )
     {
         if( ( reg_shadow & REG_BIT_TWL_REQ_BL_U ) == 0 )             // 消えた
         {
-            vreg_ctr[VREG_C_IRQ4] |= REG_BIT_TWL_BL_U_OFF;
+            set_irq( VREG_C_IRQ4, REG_BIT_TWL_BL_U_OFF );
-            if( ( vreg_ctr[VREG_C_IRQ_MASK4] & REG_BIT_TWL_BL_U_OFF ) == 0 )
-            {
-                IRQ0_ast;
-            }
         }
         else
         {
-            vreg_ctr[VREG_C_IRQ4] |= REG_BIT_TWL_BL_U_ON;
+            set_irq( VREG_C_IRQ4, REG_BIT_TWL_BL_U_ON );
-            if( ( vreg_ctr[VREG_C_IRQ_MASK4] & REG_BIT_TWL_BL_U_ON ) != 0 )
-            {
-                IRQ0_ast;
-            }
         }
     }
 
@@ -775,56 +828,93 @@ task_status_immed ntr_pmic_comm(  )
     {
         if( ( reg_shadow & REG_BIT_TWL_REQ_BL_L ) == 0 )             // 消えた
         {
-            vreg_ctr[VREG_C_IRQ4] |= REG_BIT_TWL_BL_L_OFF;
+            set_irq( VREG_C_IRQ4, REG_BIT_TWL_BL_L_OFF );
-            if( ( vreg_ctr[VREG_C_IRQ_MASK4] & REG_BIT_TWL_BL_L_OFF ) == 0 )
-            {
-                IRQ0_ast;
-            }
         }
         else
         {
-            vreg_ctr[VREG_C_IRQ4] |= REG_BIT_TWL_BL_L_OFF;
+            set_irq( VREG_C_IRQ4, REG_BIT_TWL_BL_L_OFF );
-            if( ( vreg_ctr[VREG_C_IRQ_MASK4] & REG_BIT_TWL_BL_L_OFF ) != 0 )
+        }
+    }
+#else
+
+    if( ( ( reg1_old ^ reg_shadow ) & REG_BIT_TWL_REQ_BL ) != 0 )  // バックライトの2ビットが何らか変化して、
     {
-                IRQ0_ast;
+        if( ( reg_shadow & REG_BIT_TWL_REQ_BL ) == 0x00 )          // 00になった
-            }
+        {
+            // 両方消された
+            set_irq( VREG_C_IRQ3, REG_BIT_TWL_BL_OFF );
+        }
+        else if( ( reg_shadow & REG_BIT_TWL_REQ_BL ) == REG_BIT_TWL_REQ_BL )
+        {
+            // 両方ついた
+            set_irq( VREG_C_IRQ3, REG_BIT_TWL_BL_ON );
         }
     }
 
+#endif
+
+    else
+
+
 // offリクエスト
     if( ( reg_shadow & REG_BIT_TWL_REQ_OFF_REQ ) != 0 )
     {
+#ifdef _VREG_C_NEW_
         set_irq( VREG_C_IRQ4, REG_BIT_TWL_OFF_REQ );
-        vreg_ctr[VREG_C_IRQ4] |= REG_BIT_TWL_OFF_REQ;
+#else
-        if( ( vreg_ctr[VREG_C_IRQ_MASK4] & REG_BIT_TWL_OFF_REQ ) == 0 )
+        set_irq( VREG_C_IRQ3, REG_BIT_TWL_OFF_REQ );
-        {
+#endif
-            IRQ0_ast;
-        }
     }
 
     else
 
     // リセットリクエスト
-
+    if( ( reg_shadow & REG_BIT_TWL_REQ_RST_REQ ) != 0 )
+    {
         // CODECバグ回避
         // リセット単品でなかったら無視
-//    if( ( reg_shadow & REG_BIT_TWL_REQ_RST_REQ ) != 0 )
         if( ( reg1_old ^ reg_shadow ) == REG_BIT_TWL_REQ_RST_REQ )
         {
-        vreg_ctr[VREG_C_IRQ4] |= REG_BIT_TWL_RESET_REQ;
+#ifdef _VREG_C_NEW_
-        if( ( vreg_ctr[VREG_C_IRQ_MASK4] & REG_BIT_TWL_RESET_REQ ) == 0 )
+            set_irq( VREG_C_IRQ4, REG_BIT_TWL_RESET_REQ );
-        {
+#else
-            IRQ0_ast;
+            set_irq( VREG_C_IRQ3, REG_BIT_TWL_RESET_REQ );
         }
     }
-
+#endif
 
     // バックライトが...
-
-
     EI(  );
     reg_shadow &= ~( REG_BIT_TWL_REQ_OFF_REQ | REG_BIT_TWL_REQ_RST_REQ );
     iic_mcu_write_a_byte( IIC_SLA_CODEC, CODEC_REG_PM, reg_shadow );
 #endif
     return ( ERR_FINISED );
 }
+
+
+
+/**********************************************************
+ 電池残量ICから残量を取得し、レジスタに書き込む。
+ 　電池残量ICが無い・故障などの時はとりあえず残量99%とする。
+ 　　　　　　　　↑は status_1で確認可能。電源投入時にチェックしています。
+ 　PM_init()が実行されている必要があります。
+**********************************************************/
+static void PM_get_batt_left(){
+    if(( vreg_ctr[ VREG_C_STATUS_1 ] & REG_BIT_GASGAUGE_ERR ) == 0 )
+    {
+        // 電池残量の取得
+        {
+            u8 temp[2];
+
+            iic_mcu_read( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_SOC, 2, temp );
+
+            vreg_ctr[ VREG_C_BT_REMAIN ] = temp[0];
+            vreg_ctr[ VREG_C_BT_REMAIN_FINE ] = temp[1];
+            // todo 閾値を超えたら割り込み
+        }
+    }
+    else
+    {
+        vreg_ctr[ VREG_C_BT_REMAIN ] = 99;
+    }
+}

trunk/pm.h

@@ -44,8 +44,8 @@ enum PMIC_REG_ADRS
 // TWLがSPIでPMICに投げたコマンド
 #define REG_BIT_TWL_REQ_OFF_REQ  ( 1 << 6 )
 #define REG_BIT_TWL_REQ_RST_REQ  ( 1 << 0 )
-#define REG_BIT_TWL_REQ_BL_U     ( 1 << 3 )
+#define REG_BIT_TWL_REQ_BL       ( 3 << 2 )
-#define REG_BIT_TWL_REQ_BL_L     ( 1 << 2 )
+
 
 
 
@@ -89,17 +89,17 @@ void PM_init(  );
 err PM_LCD_vcom_set(  );
 task_status_immed tski_vcom_set(  );
 
-err PM_BL_set(  );
+err PM_BL_on(  );
+err PM_BL_off(  );
 
-task_status_immed tski_PM_BL_set(  );
+task_status_immed tski_PM_BL_on(  );
+task_status_immed tski_PM_BL_off(  );
 task_status_immed tski_PM_LCD_on(  );
 task_status_immed tski_PM_LCD_off(  );
 
 
 
 //  　これを呼ぶ前に、現在温度を教えておく必要があります。
-#define PM_get_batt_left()       ( iic_mcu_read_a_byte( IIC_SLA_BT_GAUGE, BT_GAUGE_REG_SOC ) )
-
 #define PM_reset()               ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_CONT, 0x00 ) )
 
 
@@ -147,7 +147,7 @@ task_status_immed tski_PM_LCD_off(  );
 #define PM_TCOM_VCS_off() PM_VDDLCD_on()
 #define PM_VDDLCD_off() ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_VDD_LCD, 0 ) )
 
-//#define PM_set_BL( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_BL, dat ) )
+#define PM_set_BL( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_BL, dat ) )
 #define PM_set_adc1( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_DAC1, dat ) )
 #define PM_set_adc2( dat ) ( iic_mcu_write_a_byte( IIC_SLA_PMIC, PM_REG_ADRS_POW_DAC2, dat ) )
 

trunk/rtc.c

@@ -175,14 +175,6 @@ void rtc_unlock(  )
   2^6/fXT（1.953125 ms）
  ======================================================== */
 __interrupt void int_rtc_int(  )
-{
-    if( renge_flg_interval == 0 )
 {
     renge_flg_interval = 1;
-        system_time += 1;
-    }
-    else
-    {
-        NOP();
-    }
 }

trunk/sw.c

@@ -17,7 +17,7 @@
 //=========================================================
 #define INTERVAL_TSK_SW  16
 #define CLICK_THRESHOLD  3
-#define HOLD_THREASHOLD ( 600 / INTERVAL_TSK_SW )
+#define HOLD_THREASHOLD (u8)( 600 / INTERVAL_TSK_SW )
 
 
 
@@ -56,13 +56,13 @@ void tsk_sw(  )
     static u8 cnt_force_off = 0;
     static u8 task_interval = 0;
 
-    if( task_interval != system_time )
+    if( task_interval-- != 0 )
     {
         return;
     }
     else
     {
-        task_interval += (u8)( INTERVAL_TSK_SW / SYS_INTERVAL_TICK );
+        task_interval = (u8)( INTERVAL_TSK_SW / SYS_INTERVAL_TICK );
     }
 
 
@@ -131,7 +131,7 @@ void tsk_sw(  )
         }
 
         // wifi sw //
-        if( SW_wifi_count == 10 )
+        if( SW_wifi_count == HOLD_THREASHOLD )
         {
             set_irq( VREG_C_IRQ0, REG_BIT_SW_WIFI_CLICK );
         }

trunk/task_debug.c

@@ -7,6 +7,7 @@
 #include "renge.h"
 #include "pm.h"
 
+#include "accero.h"
 
 
 extern u8 command_bl_set;
@@ -27,7 +28,7 @@ void tsk_debug(  )
         if( !SW_SEL_n ){
             command_bl_set = REG_BIT_CMD_BL_U_ON | REG_BIT_CMD_BL_L_ON;
             PM_LCD_on();
-            PM_BL_set();
+            PM_BL_on();
         }
 
 //        vreg_ctr[ VREG_C_ACC_CONFIG ] = 0x03;
@@ -58,11 +59,10 @@ void tsk_debug2(  )
         str[1] = vreg_ctr[ VREG_C_STATUS ];
         str[0] = vreg_ctr[ VREG_C_RTC_SEC ];
 */
-        str[3] = vreg_ctr[ VREG_C_IRQ1 ];
+        str[3] = vreg_ctr[ VREG_C_ACC_HOSU_L ];
-        str[2] = vreg_ctr[ VREG_C_IRQ2 ];
+        str[2] = SEC;
-        str[1] = vreg_ctr[ VREG_C_IRQ3 ];
+        str[1] = vreg_ctr[ VREG_C_BT_TEMP ];
-//        str[0] = vreg_ctr[ VREG_C_STATUS ];
+        str[0] = vreg_ctr[ VREG_C_BT_REMAIN ];
-        str[0] = temp_debug_3;
 
 //    iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 2, vreg_ctr[ VREG_C_IRQ1 ] );
 //    iic_mcu_write_a_byte( IIC_SLA_DBG_MONITOR, 1, boot_ura );

trunk/task_misc.c

@@ -11,6 +11,8 @@
 
 #define INTERVAL_TSK_MISC_STAT 4
 
+
+
 /* ========================================================
  ステータスレジスタなど
  ======================================================== */
@@ -55,6 +57,22 @@ void tsk_misc_stat(  )
                 }
             }
 
+            if( diff & REG_BIT_BL )
+            {
+                // バックライトに変化有り
+                if( vreg_ctr[VREG_C_STATUS] & REG_BIT_BL )
+                {
+                    // ついた
+                    set_irq( VREG_C_IRQ3, REG_BIT_BL_ON );
+                }
+                else
+                {
+                    // 消えた
+                    set_irq( VREG_C_IRQ3, REG_BIT_BL_OFF );
+                }
+            }
+#if 0
+            todo
                     if( diff & REG_BIT_BL_U )
             {
                 // バックライトに変化有り
@@ -84,7 +102,7 @@ void tsk_misc_stat(  )
                     set_irq( VREG_C_IRQ4, REG_BIT_BL_L_OFF );
                 }
             }
-
+#endif
             if( diff & REG_BIT_BATT_CHARGE )
             {
                 // 充電状態に以下略
@@ -167,18 +185,14 @@ void tsk_misc_stat(  )
  ======================================================== */
 task_status_immed do_command(  )
 {
-    // cmd0 本体電源など
+
+    // 本体電源など
     if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_OFF_REQ )
     {
         system_status.pwr_state = OFF_TRIG;
     }
     else
     {
-        if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_FCRAM_RESET_REQ )
-        {
-            FCRAM_RST_ast;
-            wait_ms( 5 );
-        }
         if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_RESET1_REQ )
         {
             PM_reset_ast(  );
@@ -186,34 +200,41 @@ task_status_immed do_command(  )
             FCRAM_RST_ast;
             wait_ms( 5 );
         }
-        else if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_RESET2_REQ )
+        if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_RESET2_REQ )
         {
             RESET2_ast;
             wait_ms( 5 );
         }
+        if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_FCRAM_RESET_REQ )
+        {
+            FCRAM_RST_ast;
+            wait_ms( 5 );
+        }
         PM_reset_neg(  );
         RESET2_neg;
         FCRAM_RST_neg;
     }
-    vreg_ctr[VREG_C_COMMAND0] = 0;
 
-    // cmd1 液晶電源など
+    // 液晶電源など
-    command_bl_set = ( vreg_ctr[VREG_C_COMMAND1] & ( REG_BIT_CMD_BL_U_ON | REG_BIT_CMD_BL_U_OFF | REG_BIT_CMD_BL_L_ON | REG_BIT_CMD_BL_L_OFF ));
+    if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_CMD_BL_ON )
-    if( command_bl_set != 0 )
     {
-        renge_task_immed_add( tski_PM_BL_set );
+        renge_task_immed_add( tski_PM_BL_on );
+    }
+    else if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_CMD_BL_OFF )
+    {
+        renge_task_immed_add( tski_PM_BL_off );
     }
 
-    if( vreg_ctr[VREG_C_COMMAND1] & REG_BIT_CMD_LCD_ON )
+    if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_CMD_LCD_ON )
     {
         renge_task_immed_add( tski_PM_LCD_on );
     }
-    else if( vreg_ctr[VREG_C_COMMAND1] & REG_BIT_CMD_LCD_OFF )
+    else if( vreg_ctr[VREG_C_COMMAND0] & REG_BIT_CMD_LCD_OFF )
     {
         renge_task_immed_add( tski_PM_LCD_off );
     }
 
-    vreg_ctr[VREG_C_COMMAND1] = 0;
+    vreg_ctr[VREG_C_COMMAND0] = 0;
     return ( ERR_FINISED );
 }
 

trunk/vreg_ctr.h

@@ -37,6 +37,7 @@
 #define REG_BIT_SHELL_OPEN          ( 1 << 1 )
 #define REG_BIT_SHELL_CLOSE         ( 1 << 0 )
 
+#ifdef _VREG_C_NEW_
 //  VREG_C_IRQ3
 #define REG_BIT_LCD_ON              ( 1 << 5 )
 #define REG_BIT_LCD_OFF             ( 1 << 4 )
@@ -53,20 +54,36 @@
 #define REG_BIT_TWL_OFF_REQ         ( 1 << 1 )
 #define REG_BIT_TWL_RESET_REQ       ( 1 << 0 )
 
+#else
+//  VREG_C_IRQ3
+#define REG_BIT_TWL_BL_ON           ( 1 << 7 )
+#define REG_BIT_TWL_BL_OFF          ( 1 << 6 )
+#define REG_BIT_TWL_OFF_REQ         ( 1 << 5 )
+#define REG_BIT_TWL_RESET_REQ       ( 1 << 4 )
+#define REG_BIT_LCD_ON              ( 1 << 3 )
+#define REG_BIT_LCD_OFF             ( 1 << 2 )
+#define REG_BIT_BL_ON               ( 1 << 1 )
+#define REG_BIT_BL_OFF              ( 1 << 0 )
+
+#endif
+
 //  VREG_C_STATUS,
 #define REG_BIT_LCD_POW             ( 1 << 7 )
-#define REG_BIT_BL_U                ( 1 << 6 )
+#define REG_BIT_BL                  ( 1 << 6 )
-#define REG_BIT_BL_L                ( 1 << 5 )
 #define REG_BIT_BATT_CHARGE         ( 1 << 4 )
 #define REG_BIT_POW_SUPPLY          ( 1 << 3 )
 #define REG_BIT_ST_SHELL_OPEN       ( 1 << 1 )
 
+#define REG_BIT_BL_U                ( 1 << 6 )
+#define REG_BIT_BL_L                ( 1 << 5 )
+
+
 //  VREG_C_STATUS_1
 #define REG_BIT_GASGAUGE_ERR        ( 1 << 0 )
 #define REG_BIT_ACCERO_ERR          ( 1 << 1 )
 
 
-// VREG_C_COMMAND0
+#ifdef _VREG_C_NEW_
 #define REG_BIT_FCRAM_RESET_REQ     ( 1 << 3 )
 #define REG_BIT_RESET2_REQ          ( 1 << 2 )
 #define REG_BIT_RESET1_REQ          ( 1 << 1 )
@@ -86,6 +103,31 @@
 #define REG_BIT_SEND_TWL_OFF_REQ    ( 1 << 2 )
 #define REG_BIT_SEND_TWL_RESET_REQ  ( 1 << 1 )
 #define REG_BIT_SEND_TWL_PWSW_DET   ( 1 << 0 )
+#else
+
+// 暫定　コンパイルを通すため
+#define REG_BIT_CMD_BL_U_ON         ( 1 << 3 )
+#define REG_BIT_CMD_BL_U_OFF        ( 1 << 2 )
+#define REG_BIT_CMD_BL_L_ON         ( 1 << 1 )
+#define REG_BIT_CMD_BL_L_OFF        ( 1 << 0 )
+
+// VREG_C_COMMAND0
+#define REG_BIT_CMD_LCD_ON              ( 1 << 7 )
+#define REG_BIT_CMD_LCD_OFF             ( 1 << 6 )
+#define REG_BIT_CMD_BL_ON               ( 1 << 5 )
+#define REG_BIT_CMD_BL_OFF              ( 1 << 4 )
+#define REG_BIT_FCRAM_RESET_REQ     ( 1 << 3 )
+#define REG_BIT_RESET2_REQ          ( 1 << 2 )
+#define REG_BIT_RESET1_REQ          ( 1 << 1 )
+#define REG_BIT_OFF_REQ             ( 1 << 0 )
+
+// VREG_C_COMMAND1
+#define REG_BIT_SEND_TWL_BATT_EMPTY ( 1 << 4 )
+#define REG_BIT_SEND_TWL_BATT_LOW   ( 1 << 3 )
+#define REG_BIT_SEND_TWL_OFF_REQ    ( 1 << 2 )
+#define REG_BIT_SEND_TWL_RESET_REQ  ( 1 << 1 )
+#define REG_BIT_SEND_TWL_PWSW_DET   ( 1 << 0 )
+#endif
 
 
 // VREG_C_WIFI_LED
@@ -162,9 +204,15 @@ enum VREG_C
 
   VREG_C_TUNE = 0x08,
   VREG_C_SND_VOL,
+#ifdef _VREG_C_NEW_
   VREG_C_BT_TEMP,
   VREG_C_BT_REMAIN,
   VREG_C_BT_REMAIN_FINE,
+#else
+  VREG_C_BT_REMAIN,
+  VREG_C_BT_TEMP,
+  VREG_C_BT_REMAIN_FINE,  // ダミーですが
+#endif
 
   VREG_C_STATUS_1 = 0x0E,
   VREG_C_STATUS = 0x0F,

trunk/vreg_twl.c

@@ -38,7 +38,7 @@ void vreg_twl_write( u8 adrs, u8 data )
     {
       case ( REG_TWL_INT_ADRS_VOL ):
         {
-            set_irq(&vreg_ctr[ VREG_C_IRQ0 ], REG_BIT_VR_SNDVOL_CHANGE );
+            set_irq( VREG_C_IRQ0, REG_BIT_VR_SNDVOL_CHANGE );
             break;
         }
 

trunk/yav_mcu_bsr.plg

@@ -1,134 +1,16 @@
 C:\WINDOWS\system32\cmd.exe /c echo touch magic.c
 touch magic.c
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no loader.c
+"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -quvjl2wt -sainter_asm -zp -no i2c_mcu.c
-loader.c(138) : CC78K0R warning W0401: Conversion may lose significant digits
+i2c_mcu.c(119) : CC78K0R warning W0401: Conversion may lose significant digits
-loader.c(142) : CC78K0R warning W0401: Conversion may lose significant digits
+i2c_mcu.c(196) : CC78K0R warning W0401: Conversion may lose significant digits
-loader.c(145) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    3 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\loader.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no pm.c
-pm.c(189) : CC78K0R warning W0401: Conversion may lose significant digits
-pm.c(201) : CC78K0R warning W0401: Conversion may lose significant digits
-pm.c(205) : CC78K0R warning W0401: Conversion may lose significant digits
-pm.c(380) : CC78K0R warning W0401: Conversion may lose significant digits
-pm.c(621) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    5 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\pm.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no i2c_ctr.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\i2c_ctr.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no main.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\main.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no magic.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\magic.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no WDT.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\WDT.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no i2c_mcu.c
-i2c_mcu.c(103) : CC78K0R warning W0401: Conversion may lose significant digits
-i2c_mcu.c(180) : CC78K0R warning W0401: Conversion may lose significant digits
 Compilation complete,    0 error(s) and    2 warning(s) found.
 "C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\i2c_mcu.asm
 Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no i2c_twl.c
+"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\lk78k0r.exe" -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -obsr.lmf "..\..\Program Files\NEC Electronics Tools\CC78K0R\W2.10\lib78k0r\s0rm.rel"  -go85h,0FC00h,1024 -gi0FFFFFFFFFFFFFFFFFFFFh -pbsr_k0r.map -nkd -kp -gb6EFFFFh -b"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib" -bcl0rdm.lib -bcl0rm.lib -bcl0rmf.lib -i"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\lib78k0r" -dbsr_mcu.dr -s -w0  loader.rel pm.rel i2c_ctr.rel main.rel magic.rel WDT.rel i2c_mcu.rel i2c_twl.rel ini_VECT.rel led.rel rtc.rel vreg_ctr.rel vreg_twl.rel adc.rel renge.rel accero.rel self_flash.rel reboot.rel sw.rel task_debug.rel task_misc.rel task_sys.rel 
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\i2c_twl.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no ini_VECT.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\ini_VECT.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no led.c
-led.c(422) : CC78K0R warning W0401: Conversion may lose significant digits
-led.c(423) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    2 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\led.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no rtc.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\rtc.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no vreg_ctr.c
-vreg_ctr.c(60) : CC78K0R warning W0401: Conversion may lose significant digits
-vreg_ctr.c(102) : CC78K0R warning W0401: Conversion may lose significant digits
-vreg_ctr.c(103) : CC78K0R warning W0401: Conversion may lose significant digits
-vreg_ctr.c(105) : CC78K0R warning W0401: Conversion may lose significant digits
-vreg_ctr.c(107) : CC78K0R warning W0401: Conversion may lose significant digits
-vreg_ctr.c(108) : CC78K0R warning W0401: Conversion may lose significant digits
-vreg_ctr.c(110) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    7 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\vreg_ctr.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no vreg_twl.c
-vreg_twl.c(41) : CC78K0R warning W0511: Different argument types in function 'set_irq'
-vreg_twl.c(47) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    2 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\vreg_twl.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no adc.c
-adc.c(73) : CC78K0R warning W0745: Expected function prototype
-adc.c(78) : CC78K0R warning W0401: Conversion may lose significant digits
-adc.c(81) : CC78K0R warning W0401: Conversion may lose significant digits
-adc.c(96) : CC78K0R warning W0401: Conversion may lose significant digits
-adc.c(99) : CC78K0R warning W0401: Conversion may lose significant digits
-adc.c(224) : CC78K0R warning W0401: Conversion may lose significant digits
-adc.c(44) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    7 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\adc.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no renge\renge.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\renge.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no accero.c
-accero.c(91) : CC78K0R warning W0745: Expected function prototype
-accero.c(93) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    2 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\accero.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no self_flash.c
-self_flash.c(234) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    1 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\self_flash.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no reboot.c
-reboot.c(14) : CC78K0R warning W0915: Asm statement found. skip to jump optimize this function 'my_reboot'
-Compilation complete,    0 error(s) and    1 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\reboot.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no sw.c
-sw.c(66) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    1 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\sw.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no task_debug.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\task_debug.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no task_misc.c
-task_misc.c(38) : CC78K0R warning W0401: Conversion may lose significant digits
-task_misc.c(201) : CC78K0R warning W0401: Conversion may lose significant digits
-task_misc.c(30) : CC78K0R warning W0401: Conversion may lose significant digits
-Compilation complete,    0 error(s) and    3 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\task_misc.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\bin\cc78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -irenge -i"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r" -ms -qvjl1wt -sainter_asm -zp -no task_sys.c
-Compilation complete,    0 error(s) and    0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\ra78k0r.exe" -c9F0104 -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff inter_asm\task_sys.asm
-Assembly complete,     0 error(s) and     0 warning(s) found.
-"C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\lk78k0r.exe" -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -obsr.lmf "..\..\Program Files\NEC Electronics Tools\CC78K0R\W2.10\lib78k0r\s0rm.rel"  -go85h,0FC00h,1024 -gi0FFFFFFFFFFFFFFFFFFFFh -pbsr_k0r.map -nkd -kp -gb7EFBFFh -b"C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib" -bcl0rdm.lib -bcl0rm.lib -bcl0rmf.lib -i"C:\Program Files\NEC Electronics Tools\CC78K0R\W2.10\lib78k0r" -dbsr_mcu.dr -s -w0  loader.rel pm.rel i2c_ctr.rel main.rel magic.rel WDT.rel i2c_mcu.rel i2c_twl.rel ini_VECT.rel led.rel rtc.rel vreg_ctr.rel vreg_twl.rel adc.rel renge.rel accero.rel self_flash.rel reboot.rel sw.rel task_debug.rel task_misc.rel task_sys.rel 
 Link complete,     0 error(s) and     0 warning(s) found.
 "C:\Program Files\NEC Electronics Tools\RA78K0R\W1.31\bin\oc78k0r.exe" -y"C:\Program Files\NEC Electronics Tools\DEV" -_msgoff -o.\bsr.hex -nu -ki  bsr.lmf
 Object Conversion Complete,      0 error(s) and     0 warning(s) found.
 C:\WINDOWS\system32\cmd.exe /c ruby C:\Cygwin\home\fujita_ryohei\ctr\nec_s_2_bsrbin.rb bsr.hex
 C:/Cygwin/home/fujita_ryohei/ctr/nec_s_2_bsrbin.rb:2: warning: variable $KCODE is no longer effective; ignored
 
-Build Total error(s) : 0  Total warning(s) : 36 
+Build Total error(s) : 0  Total warning(s) : 2 

trunk/yav_mcu_bsr.pri

@@ -17,12 +17,12 @@ NMI=OFF
 TRESET=ON
 IRESET=OFF
 WAIT=OFF
-SysClock=None
+SysClock=8.00
-SubClock=None
+SubClock=32.768
 [Mapping]
 Count=0
 [Main]
-Geometry=123, 8, 1395, 1124
+Geometry=176, 176, 1200, 882
 Window=Max
 MDI_MAX=OFF
 Button=ON
@@ -55,7 +55,7 @@ HighSpeed1=OFF
 CPU Reset1=ON
 Symbol Reset1=ON
 [View File]
-Dir=.
+Dir=renge\
 Filter=Source
 [Debugger Option]
 Source Path=".;renge"
@@ -66,9 +66,9 @@ Offset Label=OFF
 Offset Mnemonic=ON
 Tab Count=4
 Tab Size1=*.*, 8
-Tab Size2=*.c, 8
+Tab Size2=*.asm, 8
-Tab Size3=*.s, 8
+Tab Size3=*.c, 8
-Tab Size4=*.asm, 8
+Tab Size4=*.s, 8
 Default Source=*.c;*.s;*.asm
 Default Module=*.lnk;*.lmf
 Startup Start=_@cstart
@@ -78,10 +78,10 @@ Symbol Type=OFF
 Language=C
 Kanji=SJIS
 [Source]
-Geometry=325, 260, 834, 813
+Geometry=7, 328, 821, 747
 Window=Normal
-DispStart=46
+DispStart=443
-CaretPos=89,0
+CaretPos=471,0
 Mode=Normal
 DispFile=
 Address1=
@@ -142,7 +142,7 @@ Accumulative=ON
 [Assemble]
 Geometry=0, 0, 0, 0
 Window=Hide
-DispStart=864531456
+DispStart=864338944
 CaretPos=0,0
 Address1=
 Address2=
@@ -185,7 +185,7 @@ SaveRange=Screen
 SaveStart=
 SaveEnd=
 [Memory]
-Geometry=859, 4, 550, 1064
+Geometry=0, 0, 0, 0
 Window=Hide
 Boundary=0
 Format=Hex
@@ -194,7 +194,7 @@ Endian=
 Ascii=OFF
 Idtag=OFF
 Address=
-DispStart=00004390
+DispStart=FFFFFFFF
 CaretPosData=0, 0
 CaretPosAscii=0, 0
 Address1=
@@ -251,9 +251,9 @@ Destination=0
 [I/O Port]
 Line=0
 [Stack]
-Geometry=0, 0, 0, 0
+Geometry=12, 14, 400, 300
-Window=Hide
+Window=Normal
-Boundary=0
+Boundary=13762687
 Mode=Proper
 [Sfr]
 Geometry=0, 0, 0, 0
@@ -814,7 +814,7 @@ L529=IICWL1
 L530=IICWH1
 L531=SVA1
 [Local Variable]
-Geometry=442, 879, 400, 212
+Geometry=1174, 786, 400, 300
 Window=Normal
 Boundary=13041851
 Mode=Proper
@@ -883,8 +883,8 @@ PSW=3
 ES=3
 CS=3
 [Event Manager]
-Geometry=0, 0, 0, 0
+Geometry=662, 893, 500, 200
-Window=Hide
+Window=Normal
 Sort by=Unsort
 Detail=OFF
 [Event Set]
@@ -894,17 +894,7 @@ Manager=ON
 Sort by=Unsort
 Detail=OFF
 Last Name=
-Name0=vreg_001
+Count=0
-Status0=W
-Access Size0=B
-Address Range0=EQ
-Address0=<vreg_ctr[0xe]> - <>
-Mask Address0=00000000
-Data Range0=NC
-Data0=<00000000> - <00000000>
-Mask Data0=FFFFFFFF
-Pass0=0001
-Count=1
 [Event Link]
 Geometry=0, 0, 0, 0
 Window=Hide
@@ -920,10 +910,7 @@ Manager=ON
 Sort by=Unsort
 Detail=OFF
 Last Name=
-Name0=vreg_002
+Count=0
-Element0=vreg_001
-Set0=ON
-Count=1
 [Trace]
 Geometry=0, 0, 0, 0
 Window=Hide
@@ -970,58 +957,46 @@ Detail=OFF
 Last Name=
 Count=0
 [Variable]
-Geometry=1143, 7, 440, 503
+Geometry=1165, 10, 420, 597
 Window=Normal
 Boundary=13762700
-0=.hist_tune,P,N,A,+,1
+0=.SIO10,P,S,A,+,1
-1=.vreg_ctr[8],P,N,A,+,1
+1=.system_status.pwr_state,P,N,A,+,1
-2=.comp,P,N,A,+,1
+2=.tasks_immed,P,N,A,+,1
-3=.pool,P,N,A,+,1
+3=.SDR02,H,S,A,+,1
-4=.p_buff,P,N,A,+,1
+4=.hyst_pedometer,.,N,A,+,1
-5=.p_rom,P,N,A,+,1
+Line=5
-6=.SVA0,P,S,A,+,1
-7=.IICA0EN,P,S,A,+,1
-8=.IICAIF1,P,S,A,+,1
-9=.IICAIF0,P,S,A,+,1
-10=.system_status.pwr_state,P,N,A,+,1
-11=.P2,B,S,A,+,1
-12=.PM2,B,S,A,+,1
-13=.raw_adc_temperature,P,N,A,+,1
-14=.vreg_ctr,P,N,A,+,1
-15=.reg1_old,P,N,A,+,1
-16=.reg_shadow,P,N,A,+,1
-Line=17
 [Quick Watch]
-0=raw_adc_temperature,P,A,1
+0=hyst_pedometer,P,A,1
-1=PM2,P,A,1
+1=SDR02,P,A,1
-2=P2,B,A,1
+2=tasks_immed,P,A,1
 3=system_status.pwr_state,P,A,1
-4=IICA0IF0,P,A,1
+4=SIO10,P,A,1
-5=IICA0IF,P,A,1
+5=
-6=IICAIF0,P,A,1
+6=
-7=IICAIF1,P,A,1
+7=
-8=IICA0EN,P,A,1
+8=
-9=SVA0,P,A,1
+9=
-10=p_rom,P,A,1
+10=
-11=p_buff,P,A,1
+11=
-12=pool,P,A,1
+12=
-13=comp,P,A,1
+13=
-14=vreg_ctr[8],P,A,1
+14=
-15=hist_tune,P,A,1
+15=
 [Software Break]
-Geometry=1069, 522, 500, 272
+Geometry=848, 671, 500, 200
 Window=Normal
 Width=150 30 200 100
 Name0=Swb00001
-Address0=task_sys.c#_tsk_sys+0x171
+Address0=accero.c#_tsk_cbk_accero+0x17a
 Window0=ASM
 Status0=ON
 Name1=Swb00002
-Address1=task_sys.c#_tsk_sys+0x159
+Address1=accero.c#_acc_hosu_set+0x38
 Window1=ASM
 Status1=ON
 Name2=Swb00003
-Address2=adc.c#_tsk_adc+0x102
+Address2=task_sys.c#_tsk_sys+0xcf
 Window2=ASM
 Status2=ON
 Count=3

trunk/yav_mcu_bsr.prj

@@ -223,297 +223,6 @@ ZF=0
 S=1
 E=0
 CommandFile=0
-[Options.LK78K0R 0]
-Version=100
-O0=bsr_k0r.lmf
-O1=bsr.lmf
-O2=flash.lmf
-O3=a.lmf
-G=1
-E=0
-E0=flash.elk
-E1=a.elk
-GO=1
-GOValue=85
-GOStart=FC00
-GOSizeValue=1024
-GI=1
-GIValue=FFFFFFFFFFFFFFFFFFFF
-CCZA=0
-MemInfoCheck=1
-P=1
-P0=bsr_k0r.map
-P1=bsr.map
-P2=flash.map
-P3=a.map
-MI=0
-GB=1
-GBValue=6EFBFF
-KM=1
-KD=0
-KP=1
-KL=0
-LF=0
-LL=0
-B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
-D0=bsr_mcu.dr
-D1=user_area.dr
-S=1
-W=0
-SELFCheck=1
-SELF=0
-ZB=
-Etcetera0=
-Etcetera1=boot.lmf
-CommandFile=0
-[Options.LK78K0R 1]
-Version=100
-O0=a.lmf
-G=0
-E=0
-E0=a.elk
-GO=0
-GOValue=
-GOStart=FC00
-GOSizeValue=1024
-GI=0
-GIValue=FFFFFFFFFFFFFFFFFFFF
-CCZA=1
-MemInfoCheck=0
-P=1
-P0=a.map
-MI=0
-GB=0
-GBValue=
-KM=1
-KD=1
-KP=0
-KL=0
-LF=0
-LL=0
-S=0
-W=1
-SELFCheck=0
-SELF=0
-ZB=
-CommandFile=0
-[Options.LK78K0R 2]
-Version=100
-O0=bsr.lmf
-O1=bsr_k0r.lmf
-O2=flash.lmf
-O3=a.lmf
-G=1
-E=0
-E0=flash.elk
-E1=a.elk
-GO=1
-GOValue=85
-GOStart=FC00
-GOSizeValue=1024
-GI=1
-GIValue=FFFFFFFFFFFFFFFFFFFF
-CCZA=0
-MemInfoCheck=1
-P=1
-P0=bsr_k0r.map
-P1=bsr.map
-P2=flash.map
-P3=a.map
-MI=0
-GB=1
-GBValue=7EFBFF
-KM=1
-KD=0
-KP=1
-KL=0
-LF=0
-LL=0
-B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
-D0=bsr_mcu.dr
-D1=user_area.dr
-S=1
-W=0
-SELFCheck=0
-SELF=0
-ZB=
-Etcetera0=
-Etcetera1=boot.lmf
-CommandFile=0
-OFILE=C:\78k_data\yav-mcu-basara\bsr.lmf
-[Options.LK78K0R 3]
-Version=100
-O0=bsr_bsr.lmf
-O1=bsr_k0r.lmf
-O2=bsr.lmf
-O3=flash.lmf
-O4=a.lmf
-G=1
-E=0
-E0=flash.elk
-E1=a.elk
-GO=1
-GOValue=85
-GOStart=FC00
-GOSizeValue=1024
-GI=1
-GIValue=FFFFFFFFFFFFFFFFFFFF
-CCZA=0
-MemInfoCheck=1
-P=1
-P0=bsr_bsr.map
-P1=bsr_k0r.map
-P2=bsr.map
-P3=flash.map
-P4=a.map
-MI=0
-GB=1
-GBValue=6EFBFF
-KM=1
-KD=0
-KP=1
-KL=0
-LF=0
-LL=0
-B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
-D0=bsr_mcu.dr
-D1=user_area.dr
-S=1
-W=2
-SELFCheck=0
-SELF=0
-ZB=
-Etcetera0=
-Etcetera1=boot.lmf
-CommandFile=0
-[Options.LK78K0R 4]
-Version=100
-O0=bsr_k0r.lmf
-O1=bsr.lmf
-O2=flash.lmf
-O3=a.lmf
-G=1
-E=0
-E0=flash.elk
-E1=a.elk
-GO=1
-GOValue=85
-GOStart=FC00
-GOSizeValue=1024
-GI=1
-GIValue=FFFFFFFFFFFFFFFFFFFF
-CCZA=0
-MemInfoCheck=1
-P=1
-P0=bsr_k0r.map
-P1=bsr.map
-P2=flash.map
-P3=a.map
-MI=0
-GB=1
-GBValue=6EFBFF
-KM=1
-KD=0
-KP=1
-KL=0
-LF=0
-LL=0
-B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
-D0=bsr_mcu.dr
-D1=user_area.dr
-S=1
-W=0
-SELFCheck=1
-SELF=0
-ZB=
-Etcetera0=
-Etcetera1=boot.lmf
-CommandFile=0
-[Options.LK78K0R 5]
-Version=100
-O0=bsr_bsr.lmf
-O1=bsr_k0r.lmf
-O2=bsr.lmf
-O3=flash.lmf
-O4=a.lmf
-G=1
-E=0
-E0=flash.elk
-E1=a.elk
-GO=1
-GOValue=85
-GOStart=FC00
-GOSizeValue=1024
-GI=1
-GIValue=FFFFFFFFFFFFFFFFFFFF
-CCZA=0
-MemInfoCheck=1
-P=1
-P0=bsr_bsr.map
-P1=bsr_k0r.map
-P2=bsr.map
-P3=flash.map
-P4=a.map
-MI=0
-GB=1
-GBValue=6EFBFF
-KM=1
-KD=0
-KP=1
-KL=0
-LF=0
-LL=0
-B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
-D0=bsr_mcu.dr
-D1=user_area.dr
-S=1
-W=2
-SELFCheck=0
-SELF=0
-ZB=
-Etcetera0=
-Etcetera1=boot.lmf
-CommandFile=0
-[Options.LCNV78K0R 0]
-Version=100
-LCNV_GO=0
-E=0
-CommandFile=0
-[Options.LCNV78K0R 1]
-Version=100
-LCNV_GO=0
-E=0
-CommandFile=0
-[Options.LCNV78K0R 2]
-Version=100
-LCNV_GO=0
-E=0
-CommandFile=0
-[Options.LCNV78K0R 3]
-Version=100
-LCNV_GO=0
-E=0
-CommandFile=0
-[Options.LCNV78K0R 4]
-Version=100
-LCNV_GO=0
-E=0
-CommandFile=0
-[Options.LCNV78K0R 5]
-Version=100
-LCNV_GO=0
-E=0
-CommandFile=0
-[Options.78K0R]
-BuildMode=2
-BuildMode2=K0R_dbg
-BuildMode3=BSR_dbg
-BuildMode4=BSR_rel
-BuildMode5=BSR_WM0
-DefaultMode2=1
-DefaultMode3=1
-DefaultMode4=1
-DefaultMode5=1
 [SrcFile]
 Source1=loader.c
 Source2=pm.c
@@ -1038,3 +747,294 @@ ToolSetName=(
 Tool1=CC78K0R|W2.10
 Tool2=RA78K0R|W1.31
 Tool3=ID78K0R-QB|V3.60
+[Options.LK78K0R 0]
+Version=100
+O0=bsr_k0r.lmf
+O1=bsr.lmf
+O2=flash.lmf
+O3=a.lmf
+G=1
+E=0
+E0=flash.elk
+E1=a.elk
+GO=1
+GOValue=85
+GOStart=FC00
+GOSizeValue=1024
+GI=1
+GIValue=FFFFFFFFFFFFFFFFFFFF
+CCZA=0
+MemInfoCheck=1
+P=1
+P0=bsr_k0r.map
+P1=bsr.map
+P2=flash.map
+P3=a.map
+MI=0
+GB=1
+GBValue=6EFBFF
+KM=1
+KD=0
+KP=1
+KL=0
+LF=0
+LL=0
+B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
+D0=bsr_mcu.dr
+D1=user_area.dr
+S=1
+W=0
+SELFCheck=1
+SELF=0
+ZB=
+Etcetera0=
+Etcetera1=boot.lmf
+CommandFile=0
+[Options.LK78K0R 1]
+Version=100
+O0=a.lmf
+G=0
+E=0
+E0=a.elk
+GO=0
+GOValue=
+GOStart=FC00
+GOSizeValue=1024
+GI=0
+GIValue=FFFFFFFFFFFFFFFFFFFF
+CCZA=1
+MemInfoCheck=0
+P=1
+P0=a.map
+MI=0
+GB=0
+GBValue=
+KM=1
+KD=1
+KP=0
+KL=0
+LF=0
+LL=0
+S=0
+W=1
+SELFCheck=0
+SELF=0
+ZB=
+CommandFile=0
+[Options.LK78K0R 2]
+Version=100
+O0=bsr.lmf
+O1=bsr_k0r.lmf
+O2=flash.lmf
+O3=a.lmf
+G=1
+E=0
+E0=flash.elk
+E1=a.elk
+GO=1
+GOValue=85
+GOStart=FC00
+GOSizeValue=1024
+GI=1
+GIValue=FFFFFFFFFFFFFFFFFFFF
+CCZA=0
+MemInfoCheck=1
+P=1
+P0=bsr_k0r.map
+P1=bsr.map
+P2=flash.map
+P3=a.map
+MI=0
+GB=1
+GBValue=6EFFFF
+KM=1
+KD=0
+KP=1
+KL=0
+LF=0
+LL=0
+B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
+D0=bsr_mcu.dr
+D1=user_area.dr
+S=1
+W=0
+SELFCheck=0
+SELF=0
+ZB=
+Etcetera0=
+Etcetera1=boot.lmf
+CommandFile=0
+OFILE=C:\78k_data\yav-mcu-basara\bsr.lmf
+[Options.LK78K0R 3]
+Version=100
+O0=bsr_bsr.lmf
+O1=bsr_k0r.lmf
+O2=bsr.lmf
+O3=flash.lmf
+O4=a.lmf
+G=1
+E=0
+E0=flash.elk
+E1=a.elk
+GO=1
+GOValue=85
+GOStart=FC00
+GOSizeValue=1024
+GI=1
+GIValue=FFFFFFFFFFFFFFFFFFFF
+CCZA=0
+MemInfoCheck=1
+P=1
+P0=bsr_bsr.map
+P1=bsr_k0r.map
+P2=bsr.map
+P3=flash.map
+P4=a.map
+MI=0
+GB=1
+GBValue=6EFBFF
+KM=1
+KD=0
+KP=1
+KL=0
+LF=0
+LL=0
+B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
+D0=bsr_mcu.dr
+D1=user_area.dr
+S=1
+W=2
+SELFCheck=0
+SELF=0
+ZB=
+Etcetera0=
+Etcetera1=boot.lmf
+CommandFile=0
+[Options.LK78K0R 4]
+Version=100
+O0=bsr_k0r.lmf
+O1=bsr.lmf
+O2=flash.lmf
+O3=a.lmf
+G=1
+E=0
+E0=flash.elk
+E1=a.elk
+GO=1
+GOValue=85
+GOStart=FC00
+GOSizeValue=1024
+GI=1
+GIValue=FFFFFFFFFFFFFFFFFFFF
+CCZA=0
+MemInfoCheck=1
+P=1
+P0=bsr_k0r.map
+P1=bsr.map
+P2=flash.map
+P3=a.map
+MI=0
+GB=1
+GBValue=6EFBFF
+KM=1
+KD=0
+KP=1
+KL=0
+LF=0
+LL=0
+B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
+D0=bsr_mcu.dr
+D1=user_area.dr
+S=1
+W=0
+SELFCheck=1
+SELF=0
+ZB=
+Etcetera0=
+Etcetera1=boot.lmf
+CommandFile=0
+[Options.LK78K0R 5]
+Version=100
+O0=bsr_bsr.lmf
+O1=bsr_k0r.lmf
+O2=bsr.lmf
+O3=flash.lmf
+O4=a.lmf
+G=1
+E=0
+E0=flash.elk
+E1=a.elk
+GO=1
+GOValue=85
+GOStart=FC00
+GOSizeValue=1024
+GI=1
+GIValue=FFFFFFFFFFFFFFFFFFFF
+CCZA=0
+MemInfoCheck=1
+P=1
+P0=bsr_bsr.map
+P1=bsr_k0r.map
+P2=bsr.map
+P3=flash.map
+P4=a.map
+MI=0
+GB=1
+GBValue=6EFBFF
+KM=1
+KD=0
+KP=1
+KL=0
+LF=0
+LL=0
+B0=C:\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\lib78k0r\fsl.lib
+D0=bsr_mcu.dr
+D1=user_area.dr
+S=1
+W=2
+SELFCheck=0
+SELF=0
+ZB=
+Etcetera0=
+Etcetera1=boot.lmf
+CommandFile=0
+[Options.LCNV78K0R 0]
+Version=100
+LCNV_GO=0
+E=0
+CommandFile=0
+[Options.LCNV78K0R 1]
+Version=100
+LCNV_GO=0
+E=0
+CommandFile=0
+[Options.LCNV78K0R 2]
+Version=100
+LCNV_GO=0
+E=0
+CommandFile=0
+[Options.LCNV78K0R 3]
+Version=100
+LCNV_GO=0
+E=0
+CommandFile=0
+[Options.LCNV78K0R 4]
+Version=100
+LCNV_GO=0
+E=0
+CommandFile=0
+[Options.LCNV78K0R 5]
+Version=100
+LCNV_GO=0
+E=0
+CommandFile=0
+[Options.78K0R]
+BuildMode=2
+BuildMode2=K0R_dbg
+BuildMode3=BSR_dbg
+BuildMode4=BSR_rel
+BuildMode5=BSR_WM0
+DefaultMode2=1
+DefaultMode3=1
+DefaultMode4=1
+DefaultMode5=1

trunk/yav_mcu_bsr.prk

@@ -4,32 +4,32 @@ FrameX=2
 FrameY=2
 FrameCX=1022
 FrameCY=766
-OpenFile1=i2c_mcu.c,0,330,330,1204,1087,48,321,48,0
+OpenFile1=renge\\renge_defs.h,0,330,330,1574,1087,0,47,0,0
-OpenFile2=renge\\renge_defs.h,0,330,330,1574,1087,0,47,0,0
+OpenFile2=user_define.h,0,176,176,1420,933,0,33,20,0
-OpenFile3=user_define.h,0,176,176,1420,933,0,33,20,0
+OpenFile3=rtc.c,0,308,308,1491,934,0,31,17,0
-OpenFile4=rtc.c,0,308,308,1491,934,0,31,17,0
+OpenFile4=magic.c,0,242,242,1486,999,3,8,0,0
-OpenFile5=magic.c,0,242,242,1486,999,3,8,0,0
+OpenFile5=inter_asm\self_flash.asm,0,118,281,1362,1038,0,933,0,0
-OpenFile6=inter_asm\self_flash.asm,0,118,281,1362,1038,0,933,0,0
+OpenFile6=led.c,0,286,286,1469,912,45,278,46,0
-OpenFile7=main.c,0,124,87,1368,844,0,45,0,0
+OpenFile7=task_debug.c,0,22,22,1266,779,0,21,0,0
-OpenFile8=led.c,0,286,286,1469,912,45,278,46,0
+OpenFile8=task_sys.c,0,88,88,1332,845,44,294,44,0
-OpenFile9=task_debug.c,0,22,22,1266,779,0,21,0,0
+OpenFile9=i2c_twl.c,0,110,110,1354,867,0,156,0,0
-OpenFile10=task_sys.c,0,88,88,1332,845,44,294,44,0
+OpenFile10=loader.c,0,186,351,1369,977,0,145,0,0
-OpenFile11=i2c_twl.c,0,110,110,1354,867,0,156,0,0
+OpenFile11=vreg_twl.c,0,314,110,1264,895,12,63,19,0
-OpenFile12=ProjectWindow
+OpenFile12=reboot.c,0,110,110,1354,867,5,14,14,0
+OpenFile13=sw.c,0,198,198,1442,955,12,137,19,0
+OpenFile14=vreg_ctr.c,0,66,66,1310,823,5,261,14,0
+OpenFile15=main.c,0,124,87,1368,844,0,1,0,0
+OpenFile16=task_misc.c,0,130,277,1374,1034,58,30,58,0
+OpenFile17=pm.c,0,563,282,1807,1039,0,423,0,0
+OpenFile18=vreg_ctr.h,0,154,154,1398,911,9,108,0,0
+OpenFile19=adc.c,0,275,163,1065,610,0,96,75,0
+OpenFile20=accero.c,0,176,176,1420,933,55,97,63,0
+OpenFile21=ProjectWindow
 PrjPos=0,2,754,3,253
-OpenFile13=config.h,0,225,465,1115,1086,18,39,18,0
+OpenFile22=config.h,0,225,465,1115,1086,0,1,0,0
-OpenFile14=vreg_ctr.h,0,154,154,1398,911,30,232,30,0
+OpenFile23=i2c_mcu.c,0,330,330,1204,1087,10,500,48,0
-OpenFile15=vreg_ctr.c,0,66,66,1310,823,0,157,17,0
-OpenFile16=loader.c,0,186,351,1369,977,0,145,0,0
-OpenFile17=pm.c,0,132,132,1376,889,0,189,0,0
-OpenFile18=vreg_twl.c,0,314,110,1264,895,12,63,19,0
-OpenFile19=adc.c,0,275,163,1065,610,0,96,43,0
-OpenFile20=accero.c,0,176,176,1420,933,12,173,19,0
-OpenFile21=reboot.c,0,110,110,1354,867,5,14,14,0
-OpenFile22=sw.c,0,198,198,1442,955,12,137,19,0
-OpenFile23=task_misc.c,0,130,277,1374,1034,0,49,0,0
 OpenFile24=OutputWindow
-OutputPos=0,153,1097,771,1571
+OutputPos=0,76,1020,758,1558
 ActivePRJ=yav_mcu_bsr.prj
 [ProjectWindow]
 ProjectWindowDispType=0

trunk/yav_mcu_bsr.sdb

@@ -1,7 +1,7 @@
 [SdbInfo]
 Ver=5
 [loader.c]
-T=4afa979d
+T=4afd21ca
 1=incs_loader.h
 2=fsl.h
 3=fsl_user.h
@@ -11,16 +11,16 @@ T=4afa979d
 7=rtc.h
 8=reboot.h
 [pm.c]
-T=4afbbfd8
+T=4b033701
 1=incs.h
 2=adc.h
 3=led.h
 4=pm.h
 [i2c_ctr.c]
-T=4afa8711
+T=4b024862
 1=incs.h
 [main.c]
-T=4afbb86a
+T=4b026384
 1=incs.h
 2=WDT.h
 3=rtc.h
@@ -28,31 +28,31 @@ T=4afbb86a
 5=accero.h
 6=led.h
 [magic.c]
-T=4ad3e9ff
+T=4afd21ca
 1=config.h
 [WDT.c]
-T=4aca8ef0
+T=4afd21ca
 1=incs_loader.h
 [i2c_mcu.c]
-T=4af931e2
+T=4b0272b2
 1=incs.h
 2=i2c_mcu.h
 [i2c_twl.c]
-T=4afb74bf
+T=4afd21ca
 1=incs.h
 2=i2c_twl_defs.h
 [ini_VECT.c]
-T=4ae986c0
+T=4afd21ca
 1=config.h
 [led.c]
-T=4af37126
+T=4b026f97
 1=incs.h
 2=led.h
 [rtc.c]
-T=4af7b267
+T=4b026f97
 1=incs.h
 [vreg_ctr.c]
-T=4afbbee0
+T=4b0254a4
 1=incs.h
 2=vreg_ctr.h
 3=rtc.h
@@ -60,39 +60,39 @@ T=4afbbee0
 5=accero.h
 6=pm.h
 [vreg_twl.c]
-T=4afbbfd8
+T=4b0245c3
 1=incs.h
 2=jhl_defs.h
 3=vreg_twl.h
 4=vreg_ctr.h
 [adc.c]
-T=4afbbfd8
+T=4b026f96
 1=incs.h
 2=adc.h
 3=pm.h
 4=led.h
 [renge\renge.c]
-T=4afbb784
+T=4b024862
 1=renge\renge_defs.h
 2=renge\renge_task_intval.h
 3=renge\renge_task_immediate.h
 4=WDT.h
 5=bsr_system.h
 [accero.c]
-T=4afbbfd8
+T=4b026036
 1=incs.h
 2=..\..\Program Files\NEC Electronics Tools\CC78K0R\W2.10\inc78k0r\math.h
 [self_flash.c]
-T=4af2385f
+T=4b024862
 1=incs_loader.h
 2=..\..\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r\fsl.h
 3=fsl_user.h
 4=i2c_ctr.h
 [reboot.c]
-T=4ae01bca
+T=4afd21cb
 1=incs_loader.h
 [sw.c]
-T=4afbbfd8
+T=4b026f96
 1=incs.h
 2=i2c_twl.h
 3=i2c_ctr.h
@@ -101,18 +101,19 @@ T=4afbbfd8
 6=pm.h
 7=rtc.h
 [task_debug.c]
-T=4afbb1ae
+T=4b0265df
 1=incs.h
 2=renge\renge.h
 3=pm.h
+4=accero.h
 [task_misc.c]
-T=4afbbfd8
+T=4b024578
 1=incs.h
 2=renge\renge.h
 3=pm.h
 4=accero.h
 [task_sys.c]
-T=4afb75c7
+T=4b023fdb
 1=incs.h
 2=i2c_twl.h
 3=i2c_ctr.h
@@ -122,7 +123,7 @@ T=4afb75c7
 7=rtc.h
 8=sw.h
 [incs_loader.h]
-T=4aca8c17
+T=4afd21cb
 1=jhl_defs.h
 2=user_define.h
 3=bsr_system.h
@@ -132,51 +133,51 @@ T=4aca8c17
 7=i2c_mcu.h
 8=WDT.h
 [jhl_defs.h]
-T=4afbb6e1
+T=4b023fdb
 1=config.h
 [user_define.h]
-T=4afb7698
+T=4afd21cb
 1=config.h
 [config.h]
-T=4afa41be
+T=4b0253bf
 [bsr_system.h]
-T=4af27e29
+T=4afd21ca
 [renge\renge.h]
-T=4abc82ef
+T=4b024862
 1=renge\renge_defs.h
 2=renge\renge_task_immediate.h
 [renge\renge_defs.h]
-T=4ac96e5c
+T=4b024862
 [renge\renge_task_immediate.h]
 T=4afa8168
 1=renge\renge_defs.h
 [vreg_ctr.h]
-T=4afbbf1a
+T=4b025567
 1=config.h
 [loader.h]
-T=4aca8c17
+T=4afd21ca
 1=jhl_defs.h
 [i2c_mcu.h]
-T=4af25faf
+T=4afd21cb
 [WDT.h]
-T=4aca8c17
+T=4afd21ca
 [fsl.h]
-T=4aca8c17
+T=4afd21cb
 [fsl_user.h]
-T=4aca8c17
+T=4afd21cb
 [i2c_ctr.h]
-T=4aca8c17
+T=4afd21cb
 [pm.h]
-T=4afbb7e1
+T=4b024ba8
 [rtc.h]
-T=4af40cbb
+T=4afd21cb
 [adc.h]
-T=4ae64633
+T=4afd21cb
 1=jhl_defs.h
 [led.h]
-T=4ae98e8b
+T=4afd21cb
 [incs.h]
-T=4ae508d8
+T=4afd21ca
 1=jhl_defs.h
 2=user_define.h
 3=bsr_system.h
@@ -186,22 +187,22 @@ T=4ae508d8
 7=i2c_mcu.h
 8=rtc.h
 [vreg_twl.h]
-T=4af37c30
+T=4afd21cb
 [accero.h]
-T=4aca8c17
+T=4afd21ca
 1=jhl_defs.h
 [i2c_twl_defs.h]
-T=4aca8c17
+T=4afd21ca
 [renge\renge_task_intval.h]
 T=4ac9ab84
 1=renge\renge_defs.h
 [i2c_twl.h]
-T=4aca8c17
+T=4afd21ca
 [..\..\Program Files\NEC Electronics Tools\FSL78K0R_Type02ES\V1.20\inc78k0r\fsl.h]
 T=49a3bd4e
 [..\..\Program Files\NEC Electronics Tools\CC78K0R\W2.10\inc78k0r\math.h]
 T=45f12258
 [reboot.h]
-T=4ae008e4
+T=4afd21ca
 [sw.h]
-T=4af2326b
+T=4afd21cb